Tempstar F8MTL Скачать руководство пользователя

Страница: 5 / 52

441 01 2101 05

Specifications are subject to change without notice.

Step 3 — Combustion and Ventilation Air

Section 9.3 of the NFGC, NFPA 54/ ANSI Z223.1

−

2012 Air

for Combustion and Ventilation

Step 4 — Duct Systems

Air Conditioning Contractors Association (ACCA) Manual D,

Sheet Metal and Air Conditioning Contractors National

Association (SMACNA), or American Society of Heating,

Refrigeration, and Air Conditioning Engineers (ASHRAE)

2001 Fundamentals Handbook Chapter 34 or 2000 HVAC

Systems and Equipment Handbook Chapters 9 and 16.

Step 5 — Acoustical Lining and Fibrous Glass

Duct

Current edition of SMACNA and NFPA 90B as tested by UL

Standard 181 for Class I Rigid Air Ducts

Step 6 — Gas Piping and Gas Pipe Pressure

Testing

NFPA 54 / ANSI Z223.1

−

2012; chapters 5, 6, 7, and 8 and

National Plumbing Codes

Step 7 — Electrical Connections

National Electrical Code (NEC) NFPA 70

−

2011

Step 8 — Venting

NFGC; NFPA 54 / ANSI Z223.1

−

2012 chapters 12 and 13

ELECTROSTATIC DISCHARGE (ESD)

PRECAUTIONS PROCEDURE

1. Disconnect all power to the furnace. Multiple

disconnects may be required. DO NOT TOUCH THE

CONTROL OR ANY WIRE CONNECTED TO THE

CONTROL PRIOR TO DISCHARGING YOUR BODY’S

ELECTROSTATIC CHARGE TO GROUND.

2. Firmly touch the clean, unpainted, metal surface of the

furnace chassis which is close to the control. Tools

held in a person’s hand during grounding will be

satisfactorily discharged.

3. After touching the chassis, you may proceed to service

the control or connecting wires as long as you do

nothing to recharge your body with static electricity (for

example; DO NOT move or shuffle your feet, do not

touch ungrounded objects, etc.).

4. If you touch ungrounded objects (and recharge your

body with static electricity), firmly touch a clean,

unpainted metal surface of the furnace again before

touching control or wires.

5. Use this procedure for installed and uninstalled

(ungrounded) furnaces.

6. Before removing a new control from its container,

discharge your body’s electrostatic charge to ground to

protect the control from damage. If the control is to be

installed in a furnace, follow items 1 through 4 before

bringing the control or yourself in contact with the

furnace. Put all used and new controls into containers

before touching ungrounded objects.

7. An ESD service kit (available from commercial

sources) may also be used to prevent ESD damage.

FURNACE RELIABILITY HAZARD

Improper installation or service of furnace may cause

premature furnace component failure.
Electrostatic discharge can affect electronic

components. Follow the Electrostatic Discharge

Precautions Procedure listed below during furnace

installation and servicing to protect the furnace electronic

control. Precautions will prevent electrostatic discharges

from personnel and hand tools which are held during the

procedure. These precautions will help to avoid

exposing the control to electrostatic discharge by putting

the furnace, the control, and the person at the same

electrostatic potential.

CAUTION

Figure 4

−

Multipoise Orientations

THE BLOWER IS LOCATED

TO THE RIGHT OF THE

BURNER SECTION, AND

AIR CONDITIONED AIR IS

DISCHARGED TO THE LEFT.

THE BLOWER IS

LOCATED BELOW THE

BURNER SECTION, AND

CONDITIONED AIR IS

DISCHARGED UPWARD.

THE BLOWER IS

LOCATED ABOVE THE

BURNER SECTION, AND

CONDITIONED AIR IS

DISCHARGED DOWNWARD

THE BLOWER IS

LOCATED TO THE LEFT

OF THE BURNER SECTION,

AND CONDITIONED AIR IS

DISCHARGED TO THE RIGHT.

A02097

Содержание F8MTL




















































Результаты поиска

Содержание F8MTL

Отзывы:

Похожие инструкции для F8MTL

Бренды по названию

Популярные бренды

Tempstar F8MTL, Руководство по установке

Результаты поиска

Содержание F8MTL

Отзывы:

Похожие инструкции для F8MTL

Бренды по названию

Популярные бренды