background image

 

2 – 

 

English

 

KEY TO  SYMBOLS

 

Key to symbols

 

WARNING! The machine can be a 
dangerous tool if used incorrectly or 
carelessly, which can cause serious or 
fatal injury to the operator or others.

Please read the operator’s manual 
carefully and make sure you understand 
the instructions before using the machine.

Always wear:

Protective helmet

Hearing protection

Protective goggles or a visor

Breathing mask

This product is in accordance with 
applicable EC directives.

WARNING! Dust forms when cutting, this 
can cause injuries if inhaled. Use an 
approved breathing mask. Avoid inhaling 
petrol fumes and exhaust fumes. Always 
provide for good ventilation.

WARNING! Sparks from the cutting blade 
can cause fire in combustible materials 
such as: petrol (gas), wood, dry grass etc.

Noise emission to the environment 
according to the European Community’s 
Directive. The machine’s emission is 
specified in chapter Technical data and on 
label.

Switch off the engine by moving the stop 
switch to the STOP position before carrying 
out any checks or maintenance.

Always wear protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be worn.

Run position.

Stop, with the return spring to the operating 
position.

Stop, in the fixed position.

 

Other symbols/decals on the machine refer to special 
certification requirements for certain markets.

Содержание VentMaster 3120K
























Отзывы: