background image

11

Tempest MasterBelt Operating Manual

Battery Charging and Installation

With the Lithium-Polymer batteries installed in the battery compartment, plug the AC end of the supplied 
5VDC Charger/Power Supply into a standard AC wall outlet. Open the rubberized access cover on the side of 
the MasterBelt or BeltStation and plug the USB end of the Charger/Power Supply into the USB connector. The 
Lithium-Polymer batteries will take approximately 2¾ hours to charge from completely empty to completely 
full. This time is the same with the unit turned ON or OFF. A new, fully charged battery should power a Tempest 
MasterBelt or BeltStation for approximately nine hours.  Fast charging with the supplied fast charger requires a 
temperature range of 32° – 113° F.  

Batteries can receive more than 500 charge cycles, and continue to maintain more than 70% of their power 
rating. The Tempest battery indicator will maintain its accuracy as battery life decreases.

Alternatively, remove the Lithium-Polymer rechargeable battery from the unit 
and insert it into the optional 5-Bay Battery Charger. The Lithium-Polymer 
batteries will take approximately 2½ hours to charge from completely empty to 
completely full. See the battery charger manual for additional details.

The Tempest MasterBelt and BeltStation Battery Compartment holds either one Tempest Lithium-Polymer 
rechargeable battery or three standard alkaline AA cells. Lithium-Polymer batteries are the primary power source. 
High quality alkaline AA cells may be used in situations where Lithium-Polymer batteries are not available or 
are not charged. One Lithium-Polymer battery comes standard with each Tempest MasterBelt or BeltStation. 
Additional Lithium-Polymer batteries may be purchased. Contact your dealer or distributor to purchase 

additional batteries. The Lithium-Polymer batteries supplied with your Tempest Wireless system are warranted for 90 days from the date of 
purchase.

Lithium-Polymer batteries offer 7+ hours of battery life in a MasterBelt and up to 9 hours of battery life in a BeltStation.  The batteries recharge 
in approximately 2¾ hours.

Lithium-Polymer batteries ship from the factory with approximately 50% charge. It will not damage the Lithium-Polymer batteries to use them 
without charging them first. This will, however result in shorter run time until the Lithium-Polymer battery is fully charged. When possible, charge 
Lithium-Polymer batteries to full capacity to ensure full battery life prior to use. 

Using (3) alkaline AA batteries can provide up to four hours of battery life. Use only high quality alkaline AA cells. This will provide enough time 
to fully charge the Lithium-Polymer battery.

To remove the battery door, press down on the thumb markings and pull the battery door toward the bottom of the unit. 

To remove batteries from the battery compartment, turn the MasterBelt battery side down and tap the bottom of the unit on the palm of your 
other hand. 

Please be careful to insert alkaline AA batteries according to the marked polarity. All of the alkaline AA cells must be oriented the same 
direction. If the battery cover does not close properly, the battery may not be inserted correctly.

Содержание MasterBelt 2400

































Отзывы: