56034002 1/9/2006
10
© 2006 Telular Corporation
5.3.2 Complete the Telguard Programming Data Sheet
Fill out the following
Telguard Programming Data Sheet
. The completed data sheet enables you to
properly install and test the Telguard as well as provide a valuable aid to future troubleshooting if it
becomes necessary. Detach and retain this data sheet in your customer account file for future
reference. The Telguard default setup is pre-programmed at the factory. Default setup values are
listed
and highlighted in "
bold
" type.
MEMORY
LOCATION
FIELD
DEFAULT
VALUE
SETTING
833
C/C Reporting Format
08
08 = Contact ID
851
STC Trip Output
Reporting
Normally Closed
27
Enter the
SUM TOTAL
of the events that you wish to trip the
STC relay by
ADDING
the corresponding values:
00 = STC Trip Input Not Used
01 = AC Failure
04 = not used
16 = RFC
02 = Low Battery 08 = NSC
31 = All
852
STC Trip Delay for NSC
1 1=30
Seconds
2=60 Seconds
861
CFC Number of Events
0
0 = disabled
2 = 4 attempts
1 = 2 attempts 3 = 8 attempts
862
CFC between Events
1
1 = 30 seconds
3 = 70 seconds 5 = 90 seconds
2 = 60 seconds 4 = 80 seconds 6 = 99 seconds
864
RFC Number of Attempts
2
0=Disabled 3 = 3 Attempts 6 = 6 Attempts
1=1 Attempts 4 = 4 Attempts 7 = 7 Attempts
2=2 Attempts
5 = 5 Attempts 8 = 8 Attempts
867
Standby Battery Size
3
0 = No Battery 2 = 1.2 ah 4 = 7 ah
1 = 0.8 ah
3 = 4 ah
872
AC Failure Delay
02
0-24 hours,
default = 2 hours
899
Factory Default Unit
Accessing 899 will return unit to factory default settings
5.3.3 Verify Alarm Signal Transmissions over Cellular
Trip several alarms on the C/C and verify that the central station received them by calling the central
station operator. Use a lineman's butt-set in
MONITOR MODE
and connected to Telguard's "T" and "R"
test pins to "listen" to communications between the C/C and Telguard. The ACK LED will come on solid
while waiting for an acknowledgement.
If you are having problems getting reliable alarm signal transmissions, additional adjustments may be
necessary.
♦
Recheck signal strength. You need
RSSI =
2½
(TWO LEDS ON SOLID AND THE THIRD LED
FLASHING)
for adequate signal strength. Also, check antenna connector and make sure it is seated
correctly.
♦
Call Telular Technical Service, 1-800-229-2326 extension 9
, and request the Telular
Communication Center operator to check the Telguard programming configuration for proper
operation and
proper communications format
.
5.4 S
TEP
4: C
ONNECT
S
UPERVISORY
T
RIP
O
UTPUTS
Connect and test the supervisory trip outputs to the C/C.
Activation of a local alarm or strobe light may be desirable when a trip is declared. The STC trip output can be
used directly to activate a local signaling device, provided that the trip output is not needed to trip the host
control/communicator at the same time. If both a local signal and a control trip input is required, then external
relays are needed to provide additional uncommitted contacts.
UL Listed installation of the TG-1 will at a minimum have the trip output to the host C/C to indicate low A/C
(ACFC) and low battery (LBC) conditions.
