Telonics MINI-12 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 62

background image

Telonics TCA-500C Combo Amp

50

PB-009289 Rev E

T

ELONICS

T

ILT

-B

ACK

F

OOT

A special Telonics – designed Tilt-Back Foot is provided on the following Models:

TCA-500B&C & Combo Amps
TCA-500B&C Mini-Combo Amps
External Speaker Cabinets for TCA-500B&C Mini-Combos

The Tilt-Back Foot is designed to tilt the
amplifier slightly backward to enhance
visibility of the control panel.  To deploy
the Foot, rock the amplifier backward and
pull downward on the tip of the foot until
it locks into place.

To retract the foot, rock the amplifier
backward sufficiently to remove any
weight on the foot. Push the tip of the Foot
back and upward until it is heard to snap
into its cavity on the bottom of the
amplifier cabinet.

Do Not Attempt to Stand on the
Amplifier Cabinet with the Foot
Deployed!

«
...
48
49
50
51
52
...
»

Содержание MINI-12































































Отзывы:

Нет отзывов

Похожие инструкции для MINI-12

Бренд: AB Amps Страницы: 10

Бренд: NAD Страницы: 39

Бренд: RAM Страницы: 16

Бренд: RAM Страницы: 4

Бренд: RAM Страницы: 46

Бренд: ZABKZ Страницы: 4

Бренд: Adcom Страницы: 12

Бренд: Electro-Voice Страницы: 4

Бренд: Mark Страницы: 12

Бренд: Baja Страницы: 20

Бренд: Coda Страницы: 10

Бренд: Maxmeen Страницы: 8

Бренд: R.V.R. Electronica Страницы: 36

AMP50 - XTR 1000

Бренд: W Audio Страницы: 8

Бренд: Pyle Pro Страницы: 6

Бренд: stellar labs Страницы: 7

Бренд: Harley Benton Страницы: 2

Бренд: TRU Audio Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды