tell GPRS Pager 3 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 24

tell GPRS Pager 3 Скачать руководство пользователя страница 16

16

6.7.3 Relay output settings

Setting "

Control through phone call

" function enables the specific relay to be

controlled through phone call.
In next rows events are specified and it can be set one by one to activate the desired
relays at occurrence.

01. Z1 Alarm

(alarm in zone 1)

02. Z1 Restore

(restoration of alarm in zone 1)

…
08. Z4 Restore

(restoration of alarm in zone 4)

09. Arm

(arming)

10. Disarm

(disarming)

11. Test report

(sending test report message)

Any of the above mentioned events or more of them can be selected at the same time to
activate the relays at occurrence.
It can be set for each relay (

RELAY1

and

RELAY2

), how long to remain activated after

activation at the effect of an event or a phone call. (

Max. ON time

0-254 seconds). If

value

255

is set, the specific relay will operate in bistable mode, that means if it has

been activated it will not deactivate itself, can only be deactivated through phone call (if
enabled) or will deactivate on disarm if "

Turn REL(1,2) OFF at Disarm

" is set (this

function does not work in "

Always Armed

" mode). "

Short signal (beep) on

Arm/Disarm

" function: if set, activates Relay1 impulsively on Arm/Disarm, one impulse

on Arm and two on Disarm. This function can be used to signal arming and disarming by
connecting e.g. a siren or a flashlight to this output.
Relay2 can be set to get activated on GSM network fault by setting "

REL2 indicates

GSM fault

" function.

Observation:

if the module is set in "

Always Armed

" mode with the relay(s) set as

bistable and the "

Controll through phone call

" function is not set, in case of relay

activation it cannot be deactivated only through the programming software or by
disconnecting from power supply !

«
...
14
15
16
17
18
...
»

Содержание GPRS Pager 3

























Отзывы:

Нет отзывов