Telit Wireless Solutions SC872-A Скачать руководство пользователя страница 22

Страница: 22 / 53

SC872-A

Product User Guide

Product Features

1VV0301202 Rev. 6

Page 22 of 53

2018-12-21

To enter a Periodic mode, send the following NMEA command(s):

$PMTK223

,<SV>,<SNR>,<Extension threshold>,<Extension gap>*<checksum> (

Optional)

Where:

SV = 1 to 4, default = 1

SNR = 25 to 30, default = 28

Ext. threshold = 40 000 to 180 000 ms, default = 180 000

Ext. gap = 0 to 3 600 000 ms, default = 180 000

$PMTK225

,<Type>,<Run_time>,<Sleep_time>,<2

_run_time>,<2

_sleep_time>*<checkum>

Where:

Type = 1 for Periodic (backup) mode or 2 for Periodic (standby) mode

Run_time = Full Power period (ms)

Sleep_time = Standby period (ms)

_run_time = Full Power period (ms) for extended acquisition if GNSS acquisition fails

during Run_time

_sleep_time = Standby period (ms) for extended sleep if GNSS acquisition fails during

Run_time

Example:

$PMTK225,1,3000,12000,18000,72000*16

for periodic mode with 3 s navigation and 12 s sleep in backup state.

The acknowledgement response for the command is:

$PMTK001,225,3*35

To exit Periodic Sleep mode, send the NMEA command

$PMTK225,0*2B

just after the module wakes up from a previous sleep cycle.

AlwaysLocate™ Modes

AlwaysLocate™ is an intelligent controller of the Periodic mode where the main supply pin

VCC_IN is still powered, but power distribution is controlled internally. Depending on the

environment and motion conditions, the module can autonomously and adaptively adjust the

parameters of the Periodic mode, e.g. RF on/off ratio and fix rate, to achieve a balance in

positioning accuracy and power consumption. The average current drain will vary based on

conditions.

To enter an AlwaysLocate mode, send the following NMEA command:

$PMTK225,<mode>*<checksum><CR><LF>

Where mode = 8 for AlwaysLocate (standby) mode or 9 for AlwaysLocate (backup) mode

Example:

$PMTK225,9*22

The acknowledgement response for the command is:

$PMTK001,225,3*35

To exit AlwaysLocate mode, send the NMEA command:

$PMTK225,0*2B

just after the module wakes up from its previous sleep cycle.

Содержание SC872-A






















































Результаты поиска

Содержание SC872-A

Отзывы:

Бренды по названию

Популярные бренды

Telit Wireless Solutions SC872-A, Руководство пользователя

Результаты поиска

Содержание SC872-A

Отзывы:

Бренды по названию

Популярные бренды