manualshive.com logo in svg

Telit Wireless Solutions BlueMod+S50/AI, Руководство пользователя по оборудованию

Поделиться
Скачать
Telit Wireless Solutions BlueMod+S50/AI Скачать руководство пользователя страница 41

S50 Hardware User Guide 

1VV0301505 Rev. 1  

Page 

41

 of 

53 

2018-03-02 

 

FCC Compliance 

The S50/AI  and the S50/AP  have  been tested to fulfill the FCC 
requirements. Test reports are available on request. 

 

9.2.1. 

FCC Grant 

The actual version of the FCC Grant can be downloaded from the Telit Download Zone:  

https://www.telit.com/support-training/download-zone/ 

Take note that you have to register to get access to the Download Zone. 

 

9.2.2. 

FCC Statement 

This device complies with 47 CFR Part 2 and Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 

(1)  this device my not cause harmful interference, and  

(2)  this device must accept any interference received, including interference that may 

cause undesired operation. 

 

9.2.3. 

FCC Caution 

 

 

WARNING: 

Changes or modifications made to this equipment not expressly 
approved by Telit may void the FCC authorization to operate this 
equipment 

 

 

9.2.4. 

FCC Warning 

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user 
is encouraged to try to correct the interference by one or more of the following measures: 

•

 

Reorient or relocate the receiving antenna. 

•

 

Increase the separation between the equipment and receiver. 

•

 

Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected. 

Consult the dealer or an experienced radio/TV technician for help. 

 

Содержание BlueMod+S50/AI






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды