S42
Hardware User Guide
1VV0301303 Rev. 11
Page 36 of 85
2021-05-06
Not Subject to NDA
4.3.
Application Specific CEN Pin Configuration
Pin Types: PU
–
pull-up; PD
–
pull-down; PWR
–
Power; I
–
Input; O
–
Output; I/O
–
bidir.; OD
–
open drain; PP
–
push/pull;
RF: RadioFreq; DIS
–
Disconnected; LFXO Low Frequency Crystal I/O
Pin Name
Signal
CEN-
Function
Type
Act
Description
Notes
E-6
VSUP1
Power
PWR
+3,0V nom.
F-6
VSUP2
Power
PWR
+3,0V nom
C-1
not connected
May be connected to VSUP
A-7,E-7,F-7,
B-[5,6,7,8],
C-[5,6,7,8],
D-8, E-8, F-8
GND
GND
PWR
Ground
All GND pins must be connected
A-8
ANT PIN
none
leave open (reserved for ext. antenna) (4,9)
B-1
EXT-RES#
Reset
I-PU
L
User Reset
A-6
XL-IN/ SCLK
XTAL/SCLK
LFXO
leave open if no ext. XTAL is
connected
F-4
UART-TXD
TXD
O-PP
Serial Data OUT
(6)
D-2
UART-RXD
RXD
I
Serial Data IN
(6)
D-7
UART-RTS#
/RTS
O-PP
L
Flow Control/IUC; refer to
(1,6)
F-3
UART-CTS#
/CTS
I / I-PD
L
Flow Control/IUC; refer to
(6,8)
B-4
IUR-OUT#
/IUR-OUT
O-PP / DIS L
UICP Control; refer to
(3,8)
D-5
IUR-IN#
/IUR-IN
I / DIS
L
UICP Control; refer to
(3,8)
D-3
GPIO[0]
DIS
GPIO [I2C-SCL]
(3)
B-2
GPIO[1]
DIS
GPIO [I2C-SDA]
(3)
D-1
GPIO[2]
IOC
DIS
GPIO [SPI-MOSI]
(3)
E-4
GPIO[3]
IOB
O / DIS
GPIO
(3)
D-4
GPIO[4]
HANGUP
I-PD
optional; refer to
F-2
GPIO[5]
IOD
DIS
GPIO [SPI-MISO]
(3)
C-4
GPIO[6]
reserved
DIS
GPIO
(3)
C-3
GPIO[7]
DNU
DIS
GPIO
(3)
E-2
GPIO[8]
IOA
O / DIS
GPIO [SPI-SCK] [DEVICE READY#]
(3)
A-3
NFCANT1
NFC
RF
A-1
GPIO[10]
DNU
DIS
leave open
(4)
A-4
NFCANT2
NFC
RF
A-2
GPIO[9]
DNU
DIS
leave open
(4)
F-1
TESTMODE#
reserved
I-PU / DIS
L
connect to test pad
(6,7)
E-1
BOOT0
reserved
I-PD / DIS
connect to test pad
(6,7)
E-3
SWDIO
reserved
I/O-PU
leave open (Serial Wire Debug)
D-6
SWCLK
reserved
I-PD
leave open (Serial Wire Debug)
C-2
GPIO[13]
DNU
DIS
leave open
(4)
B-3
GPIO[11]
DNU
DIS
leave open
(4)
A-5
XL-OUT
XTAL SCLK
LFXO
leave open if no ext. XTAL is
connected
F-5
GPIO[14]
DNU
DIS
leave open
(4)
E-5
GPIO[12]
DNU
DIS
leave open
(4)
Notes:
(1) a discrete pull up resistor is used
(3) function depends on firmware
(4) DNU: Do Not Use, Do Not Connect
(6) signal must be accessible for homologation purposes. Refer to 3.10 Test Mode
(7) signals sampled at startup time. TESTMODE# is I-PU, BOOT0 is I-PD during sampling time only, I-DIS otherwise
(8) Pin Type depends on UICP status. Refer to 3.3.5 Dynamic I/O Signal Type Changes Depending on UICP Status
(9) for compatibility to SR this pin is reserved for an external antenna and must be left open
Table 11: Application Specific Pin Assignments, CEN
Содержание BLUEMOD+S42/AI/ADC/LUA
