Telex Communications Forum FOH Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 62

background image

FORUM OPERATION AND MAINTENANCE MANUAL 9601

PAGE 16

MODULE DESCRIPTIONS

The input modules are provided with rear panel connectors for
Microphone Pon XLR), and Line Pjack), both balanced. Insert send
and return signals are available on a single stereo jack socket, and
are unbalanced. A Direct Output, unbalanced and ground sensing,
is also available via a jack socket on the rear panel.

Wiring of the XLR and jack connectors follows normal
conventions, so that compatibility with existing cables is provided
where possible.

XLRQ

Pin 1

Ground

Pin 2

ve Phot)

Pin 3

Signal -ve Pcold)

Jack

Line

Insert

Direct Output

Tip

Hot P+ve)

Send

Hot P+ve)

Ring

Cold

Return

Ground Sense

Sleeve

Ground

Ground

Ground

Blanking panels are fitted to the main chassis to allow the fitting of
multiway connectors. Consult your authorised dealer for more
information.

All balanced XLR inputs are wired to the international standard of
Pin 2 HOT. If you need to connect unbalanced equipment to inputs
or outputs, wire the cold terminal to Pin 3 for XLRs or the Ring for
jacks.

The microphone input is suitable for use with balanced, low
impedance microphones P150-200 ohms).

Do not use dynamic, unbalanced or battery powered microphones
with the +48 volt phantom power switched on damage to the
microphone may result.

The gain of this section is variable from 6dB to 76dB, to give an
output of +4dB at the stereo mix outputs. This corresponds to a
sensitivity of -2dBu to -72dBu.

«
...
14
15
16
17
18
...
»

Содержание Forum FOH































































Отзывы:

Нет отзывов

Похожие инструкции для Forum FOH

TRAKTOR KONTROL S4

Бренд: Native Instruments Страницы: 85

Бренд: DV Mark Страницы: 8

Бренд: Alto Professional Страницы: 8

Бренд: Titanium Страницы: 20

Бренд: Hamilton Beach Страницы: 24

Evolution Orange Underdrive

Бренд: Mad Professor Страницы: 2

Бренд: Clatronic Страницы: 42

INFINITE MINI SAMPLE SUSTAINER

Бренд: TC Electronic Страницы: 17

Бренд: Racing Страницы: 23

Бренд: RSS Страницы: 36

Бренд: Samson Страницы: 12

Бренд: Samson Страницы: 3

Бренд: Fulltone Musical Products Страницы: 2

Бренд: Klarstein Страницы: 21

Бренд: A/S WODSCHOW & CO Страницы: 24

Бренд: Toa Страницы: 8

Бренд: Whirlwind Страницы: 1

Бренд: Termozeta Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды