English
- 42 -
Software Upgrade
<RXU79LVFDSDEOHRI¿QGLQJDQGXSGDWLQJDXWRPDWLFDOO\
via the Aerial/Cable/Satellite signal.
Software upgrade search via user interface
Simply navigate on your main menu. Choose
Settings
and select
Other Settings
menu. In
Other Settings
menu navigate on to the
Software for Upgrade
item
and press
OK
button. In
Upgrade Options
menu
select
Scan for upgrade
and press
OK
button to
check for a new software upgrade.
If a new upgrade is found, it starts to download
the upgrade. Press
OK
to continue with the reboot
operation.
3 AM search and upgrade mode
While the TV is connected to an aerial signal. If
Automatic scanning
in the
Upgrade Options
menu
is
Enabled
, the TV wakes up at 03:00 and searches
broadcast channels for new software upgrades. If
new software is found and downloaded successfully,
the next time the TV powers up, it will have the new
software version.
Note: If the TV fails to come on after the upgrade unplug the
TV for 2 minutes and plug in again.
Troubleshooting & Tips
Tv will not turn on
Make sure the power cord is plugged in securely to
wall outlet. The batteries in the remote control may be
exhausted. Press the Power button on the TV.
Poor picture
Have you selected the correct TV system?
Low signal level can cause picture distortion.Please
check antenna access.
Check if you have entered the correct channel
frequency if you have done manual tuning.
The picture quality may degrade when two devices
are connected to the TV at the same time. In such
a case, disconnect one of the devices.
No picture
No Picture means that your TV is not receiving a
transmission. Have you selected the correct button on
the remote control? Try once more. Also make sure
the correct input source has been selected.
Is the antenna connected properly?
Is the antenna cable damaged?
Are suitable plugs used to connect the antenna?
If you are in doubt, consult your dealer.
No sound
Has the TV been set to mute? To cancel mute, press the
“
” button, or increase the volume level.
Sound is coming from only one speaker. Is the balance
set to one extreme? See Sound Menu section.
Remote control - does not operate
The batteries may be exhausted. Replace the
bateries.
Input sources - can not be selected
If you cannot select an input source, it is possible that
no device is connected. if not
Check the AV cables and connections if you have tried
to connect a device.
Nero MediaHome Installation
To install Nero MediaHome, please proceed as
follows:
Note: To use DLNA function, this software should be installed
to your PC.
1.
Enter the link below completely in the adress-
bar of your web browser.
http://www.nero.com/mediahome-tv
2.
Click the
Download
button on the opening
SDJH7KHLQVWDOODWLRQ¿OHZLOOEHGRZQORDGHG
onto your PC.
3.
After the download is completed, double click
RQWKHLQVWDOODWLRQ¿OHWRVWDUWWKHLQVWDOODWLRQ
The installation wizard will guide you through
the installation process.
Internet Connection Not Available / DLNA Mode
Not Operating
,IWKH0$&DGGUHVVDXQLTXHLGHQWL¿HUQXPEHURI
your PC or modem has been permanently registered,
it is possible that your TV might not connect to
the internet. In such a case, the MAC address is
authenticated each time when you connect to the
internet. This is a precaution against unauthorized
access. Since your TV has its own MAC address,
your internet service provider cannot validate the MAC
address of your TV. For this reason, your TV cannot
connect to the internet. Contact your internet service
provider and request information on how to connect
a different device, such as your TV, to the internet.
It is also possible that the connection may not be
available due to a firewall problem. If you think
this causes your problem, contact your internet
VHUYLFHSURYLGHU$¿UHZDOOPLJKWEHWKHUHDVRQRID
connectivity and discovery problem while using the TV
in DLNA mode or while browsing via DLNA.
