Teledyne SyriXus 1000x Скачать руководство пользователя страница 78

Страница: 78 / 214

SyriXus Series Pumps Installation and Operation Guide
Section 3 Basic Programming and Operation

3-20

EAR99 Technology Subject to Restrictions Contained on the Cover Page

NOTE

If you make an error, press CLEAR ENTRY to delete one character
at a time.

4. Press ENTER once the desired pressure is displayed.
5. Press RUN to initiate pump operation.

3.10.3 Dispense Mode

For applications such as reactant feed and batch delivery where a

specified volume is pumped, use Dispense Mode. Dispense Mode flow

rate begins at zero, ramps up to level out at the programmed flow rate,

then ramps back down to zero, delivering a precise specified volume.

The slope rate and run time are dependent upon the pump model

being used.

Figure 3-11 Depiction of dispense mode sequence

NOTE

For time-controlled delivery, you must run the pump in standard Gra-
dient Mode, as described in Section 4 "Gradient Pumping for Pres-
sure, Flow, and Concentration Modes".

•

In order to access Dispense Mode control, the pump must be in

Constant Flow Mode. Press CONST FLOW to enter this mode.

Toggle Dispense Mode OFF or ON by pressing DISP. Note that

pressing the DISP key while in Constant Pressure Mode has no

effect.

•

To adjust the flow rate, press

FLOWRATE

(

)

, enter the desired

rate using the number keys, and press

ENTER

•

To specify the volume of the batch delivered, press

VOLUME

(

)

enter the desired volume using the number keys, and press

ENTER

•

To dispense the batch, press

RUN

. The sequence runs once, then

stops. To repeat the sequence, press

RUN

again.

NOTE

When the system is in Dispense Mode, all Gradient Modes, Con-
stant Pressure Mode, auto-refill, and serial control are unavailable
until Dispense Mode is turned OFF.

Specified Flow

Start

Stop

ramp up

ramp down

Содержание SyriXus 1000x























































































































































































































Результаты поиска

Содержание SyriXus 1000x

Отзывы:

Похожие инструкции для SyriXus 1000x

Бренды по названию

Популярные бренды

Teledyne SyriXus 1000x, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SyriXus 1000x

Отзывы:

Похожие инструкции для SyriXus 1000x

Бренды по названию

Популярные бренды