manualshive.com logo in svg

Teledyne PROTEGE ZM, Руководство пользователя

Поделиться
Скачать
Teledyne PROTEGE ZM Скачать руководство пользователя страница 23

PROTÉGÉ ZM

PORTABLE, ZERO-MAINTENANCE, SINGLE-GAS MONITOR

MAINTENANCE

087-0047, Rev. G/December 2019

4-3

4.1.3. O

2 

CALIBRATION USING THE FRONT BUTTON

1. Press and hold the front button for four (4) seconds.
2. CAL displays and the O

2

 icon flashes.

3. After a successful calibration, the monitor emits one (1) beep, vibrates and the LEDs flash.
4. If unsuccessful, the monitor will not beep or flash and will continue displaying CAL. 

If repeated calibrations fail, remove from service.

4.2. Self-test

Prior to daily use, the device prompts for a self-test. This ensures safe operation of the monitor. 

During the self-test, the audio, visual and vibration alarms are activated and the sensor is tested. 

Table 4-1:

 

Self-Test Procedure

 details the self-test process.

WARNING: ONLY PERFORM 

O

2

 CALIBRATION IN NORMAL AIR (20.9% OXYGEN) 

THAT IS FREE OF HAZARDOUS GASES.

WARNING: THE SELF-TEST DOES NOT REPLACE THE NEED TO BUMP TEST OR 

CALIBRTATE, WHICH VERIFIES THE MONITOR’S RESPONSE TO GAS.

Table 4-1: Self-Test Procedure

LCD Display

Steps

When the TEST icon appears, a self-test is required.

Press the monitor’s button to perform the self-test.

This screen will appear. Ensure:

•

The monitor emits one audible beep

•

All LEDs light and monitor vibrates

•

All LCD display elements appear

•

Test icon flashes

Next, the LOW alarm and HIGH alarm set points are displayed.

Содержание PROTEGE ZM



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды