manualshive.com logo in svg

Teledyne Princeton Instruments IsoPlane 81, Руководство пользователя

Поделиться
Скачать
Teledyne Princeton Instruments IsoPlane 81 Скачать руководство пользователя страница 51

51

Appendix D:

Internal Shutter

Each IsoPlane 81 is shipped with an internal mechanical shutter that can be replaced in 
the field. This appendix provides information about the removal and installation of this 
internal shutter.

D.1

Required Tools

The following tools are required to remove and install an internal shutter on the 
IsoPlane 81:

•

#1 Phillips head screwdriver;

•

3/8” Allen wrench.

D.2

Internal Shutter Removal Procedure

Perform the following procedure to remove the internal shutter from the IsoPlane 81:

1.

Disconnect all cables and other equipment/accessories from the IsoPlane 81.

2.

Carefully turn the IsoPlane 81 over onto a clean, flat, dry, sturdy surface so that the 
underside of the chassis is accessible.

3.

Use a #1 Phillips head screwdriver to loosen/remove each of the four (4) Phillips 
head screws securing the shutter access panel to the underside of the IsoPlane 81 
chassis. See Figure D-1.

Figure D-1:

Remove Shutter Access Panel: Underside of IsoPlane 81

4.

Once the access panel has been removed, use the 3/8” Allen wrench to loosen the 
two Allen screws that are visible.

5.

Carefully disconnect the two-conductor electrical shutter cable.

6.

Carefully slide the shutter down to remove it.

Содержание Princeton Instruments IsoPlane 81































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды