manualshive.com logo in svg

Teledyne Princeton Instruments IsoPlane 81, Руководство пользователя

Поделиться
Скачать
Teledyne Princeton Instruments IsoPlane 81 Скачать руководство пользователя страница 22

22

IsoPlane

®

 81 Imaging Spectrometer System Manual

 Issue 1

4.3.1

Required Tools

The following tools are required to focus a slit:

•

5/64 Allen wrench

•

#1 Phillips head screwdriver

4.3.2

Focus Procedure

Perform the following procedure to focus the slit:

1.

Illuminate the slit with light from the IsoPlane 81 atomic emission wavelength 
calibration lamp.

NOTE:

If you do not have an IsoPlane 81 atomic emission 
wavelength calibration lamp, use a suitable atomic emission 
lamp.

2.

If necessary, within LightField, on the Experiment Setting tab, open the Regions of 
Interest expander and select Bin Center 10 rows. See Figure 4-1.

Figure 4-1:

Configure Regions of Interest

3.

On the Common Acquisition Settings expander, configure an Exposure Time of 
50 ms. See Figure 4-2.

Содержание Princeton Instruments IsoPlane 81































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды