manualshive.com logo in svg

Teledyne Princeton Instruments IsoPlane 81, Руководство пользователя

Поделиться
Скачать
Teledyne Princeton Instruments IsoPlane 81 Скачать руководство пользователя страница 12

12

IsoPlane

®

 81 Imaging Spectrometer System Manual

 Issue 1

•

Diffraction Grating;

Each IsoPlane 81 is shipped with a user-replaceable diffraction grating already 
installed in the instrument. Additional gratings may be purchased separately.

•

Focusing  CUBE;

A Focusing CUBE is shipped with each IsoPlane 81. This CUBE houses an f/4 
double achromatic lens with a clear aperture diameter of 7.5 mm.

•

USB  3.0  data  interface  cable;

•

External power supply.

2.1

Experiment Interface Panel

Figure 2-2 illustrates the IsoPlane 81’s Experiment Interface Panel.

Figure 2-2:

IsoPlane 81 Experiment Interface Panel

Table 2-1 provides information about experiment interface ports and equipment.

2.2

Power and Data Interface Panel

Figure 2-3 illustrates the IsoPlane 81 Power and Data Interface Panel where all data 
input/output ports, as well as the input power connector, are located.

Table 2-1:

Experiment Interface Ports and Equipment

Item

Description

Accessory Port

Compatible with IsoPlane 81 CUBES. Extensible to Thorlabs

®

 30 mm 

Cage System.

Entrance Slit

User-changeable entrance slit.

Entrance Slit Carrier

User-changeable entrance slit carrier (not shown in picture).

Slit Focus

Requires a 5/64” Allen wrench. Used to focus the system.

Threaded Aperture

SM-1, 1-inch diameter.

Содержание Princeton Instruments IsoPlane 81































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды