Teledyne Optima Скачать руководство пользователя страница 101

Страница: 101 / 112

Section 5 Maintenance

5-3

5.3 Cleaning the Sample

Chamber

To clean the sample chamber:

1. Stop or Pause the program.

2. Remove the chamber from the sampler.

3. Remove the 10 screws that hold the lid and

chamber body together.
Place the chamber parts into warm soapy
water and clean the chamber and
liquid-sensor electrodes using a brush or
sponge.

4. Assemble the chamber using the screws. Be

sure that the seal is properly seated and the
screws are tight. Loose screws or improperly
placed seal can cause a vacuum leak.

5. Install the sample chamber back into the

unit.

5.3.1 Sample Chamber Removal

To remove the sample chamber:

1. Unscrew the white hose fittings on top of

the sample chamber and loosen the
compression nut. Slide the stainless steel
intake tube in.

2. Use the lever to loosen the set collar.

3. Lift the sample chamber out of the collar.

4. Remove the stainless steel intake tube from

the chamber and the two wires from the
liquid-sensor electrodes.

Содержание Optima

















































































































Результаты поиска

Содержание Optima

Отзывы:

Teledyne Optima, Карманный справочник, Страница: 101 / 112

Результаты поиска

Содержание Optima

Отзывы: