manualshive.com logo in svg

Teledyne HVG-2020B, Инструкция по эксплуатации, Страница: 6 / 40

Поделиться
Скачать
Teledyne HVG-2020B Скачать руководство пользователя страница 6

HVG-2020B Instruction Manual

 

 EAR99 Technology Subject to Restrictions Contained on the Cover Page

 

Page 6 of 40 

 

 

Features 

COLOR DISPLAY WITH TOUCH PANEL.

  The HVG-2020B has an optional integrated touch panel color LCD 

display. This gives the user easy configurability, stand-alone operation and local control over the instrument. 

SUPERIOR ACCURACY.

  The output of the transducer is thermally compensated and linearized to provide 

accuracy of ± (0.1% of r 0.3 Torr) between 1000 Torr and 10 Torr, better than ± (5% of r 
0.00025 Torr) between 10 Torr and 1 mTorr, and better than 10% of r 0.00025 mTorr less than 1 mTorr 
after zero adjustment.  

GAS CORRECTION.

  The piezo-resistive sensor is media isolated and provides a direct pressure measurement 

that is gas species independent. There are internal corrections available for the Pirani sensor when used with 
other gases. 

NO ELASTOMERS.

  The vacuum envelope of the HVG-2020B is entirely 300 series stainless steel with welded 

construction and glass-to-metal seals.  Using metal seal vacuum connections eliminates the permeation, 
degradation and outgassing problems of elastomer O-rings. 

FLEXIBLE POWER REQUIREMENTS.

  The HVG-2020B can operate with any power supply capable of providing 12 

– 36 VDC via the 9-pin D connector or a 2 mm bayonet jack connection. 

DIGITAL COMMUNICATIONS.

  The HVG-2020B is equipped with RS232/RS485 and USB for digital 

communications. The USB connector serves as a virtual COM port for serial communication, eliminating the 
need for a USB to Serial converter. 

ANALOG OUTPUTS.

  The pressure is available in analog form as either a voltage or current signal on either a 

logarithmic or linear scale. The 0-20 mA or 4-20 mA current option gives the user the advantages of a current 
loop output to minimize environmental noise pickup and signal loss over long cable runs. 

TTL ALARMS.

  Two alarm signals are provided with an open-drain configuration, one to indicate when pressure 

goes above a value and the other below a value. 

LED INDICATORS.

  Two LEDs provide instrument status and system pressure information. 

 

 

Содержание HVG-2020B









































Отзывы:

Нет отзывов