Teledyne HVG-2020B Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 40

Teledyne HVG-2020B Скачать руководство пользователя страница 23

HVG-2020B Instruction Manual

EAR99 Technology Subject to Restrictions Contained on the Cover Page

Page 23 of 40

3.3.1. Screen Orientation

The top of the screen is indicated and will rotate 90° each time the screen is pressed.

3.3.2. Set Zero

The Set Zero menu will set the pressure reading to zero and should only be done if the actual pressure

is known to be well below 1x10

-4

Torr. If the pressure reading is too large, a warning screen will appear

asking if the user is certain they want to do this operation.

3.3.3. Device Info

The user may view the serial number, analog output setting, calibration date, gauge type, the I/O and
main board firmware revision levels, and current system errors.

3.3.4. Analog Output

The user may select non-linear, linear or logarithmic output. If logarithmic is selected, the user may
select a given full scale/slope combination or a custom option. The custom selection must be set using
serial communications.
The user may then select voltage or current output range: 0–1 V, 0–5 V, 0–10 V, 0–20 mA or 4–20 mA.

3.3.5. Gas Select

The user may select from the available gas options Refer to section 4.5 for specific values of the gas
selections. The user may select a pre-defined gas or a custom gas. The custom selections must be set
using serial communications.

The gases are as follows: Nitrogen, Air, Helium, Argon, Hydrogen, CF4, SF6, Custom 1, Custom 2

3.3.6. Serial Port

The user may select either RS232 or RS485 serial communications. After selecting the type, pressing

the arrow icon will take the user to the baud rate selection There are 5 baud rates available: 9600,
19200, 38400, 57600 and 115200. If RS485 was selected, additional sub-menu screens will appear
allowing the user to select the address and termination resistor state. At the end of the selection sub-
menus, the user can accept or canel the selections shown.

3.3.7. Restore Factory Defaults

This selection allows the user to reset the configuration of the gauge back to its original factory setup.

A warning screen will appear asking if the user is certain they want to perform this operation.

«
...
21
22
23
24
25
...
»

Содержание HVG-2020B









































Отзывы:

Нет отзывов