Teledyne HASTINGS HFC-302 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 32

Teledyne HASTINGS HFC-302 Скачать руководство пользователя страница 13

301/303/305/306/307 Flowmeters and Controllers Instruction Manual

EAR99 Technology Subject to Restrictions Contained on the Cover Page

Page 13 of 32

Electrical Connections

If a power supply from Hastings Instruments is used, installation consists of connecting the 300 series cable

from the “D” connector on the rear of the power supply to the “D” connector on the top of the flow
meter/controller. The “H” pin-out requires cable AF-8-AM (grey molded back-shell). The “U” pin-out requires
cable # 65-791 (black molded back-shell).

If a different power supply is used, follow the instructions below when connecting the flow instrument and
refer to either table 2.1 or 2.2 for the applicable pin-out. Also see section 1.3 for the 4-20 mA connections.

The power supply used must be bipolar and capable of providing the appropriate current draws mentioned in
section 2.2.  These voltages must be referenced to a common ground. One of the “common” pins must be
connected to the common terminal of the power supply.  Case ground should be connected to the AC ground
locally.  The cable shield (if available) should be connected to AC ground at the either the power supply end,

or the instrument end of the cable, not at both. Pin 6 is the output signal from the flow meter. The standard
output will be 0 to 5 VDC, where 5 VDC is 100% of the rated or full-scale flow.

The command (set point) input should be a 0-5 VDC signal (or 4-20mA if configured as such) and must be free of
spikes or other electrical noise, as these would generate false flow commands that the controller would
attempt to follow. The command signal should be referenced to signal common.

A valve override command is available to the flow controller. Connect the center pin of a single pole, three-
position switch (center off) to the override pin. C15 VDC to one end of the three-position switch, and
-15 VDC to the other end. The valve will be forced full open when +15 VDC is supplied to the override pin, and

full  closed  when  -15  VDC  is  applied.    When  there  is  no  connection  to  the  pin  (the  three-position  switch  is
centered)  the  valve  will  be  in  auto  control  and  will  obey  the  0-5  VDC  commands  supplied  to  command  (set-
point) input.

WARNING:

Care must be taken to avoid any high voltages that may be present when dealing

with power supplies. Power supplies used with 300 Series instruments should be power limited
to no more than 150 VA max. The available current for each 300 Series instrument connected
to a power supply should not exceed 1.6 A.

WARNING:

Care must be taken to avoid any high voltages that may be present when dealing

with power supplies.

«
...
11
12
13
14
15
...
»

Содержание HASTINGS HFC-302

































Отзывы:

Нет отзывов