Teledyne HASTINGS HFC-302 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 32

Teledyne HASTINGS HFC-302 Скачать руководство пользователя страница 10

301/303/305/306/307 Flowmeters and Controllers Instruction Manual

EAR99 Technology Subject to Restrictions Contained on the Cover Page

Page 10 of 32

Accessories

1.4.1. Power Supplies

Hastings power supplies are available in one or four channel versions. They convert 100, 115 or 230VAC
to the ±15 VDC required to operate the instruments and provide a digital indication of the instrument

output. Hastings power supplies are power limited to no more than 150 VA max (fused). Interface
terminals for the analog output signals and a main power on/off switch are located on the rear panel as
well. For safety reasons it is recommended that the power supply (and on/off switch) be kept near the
flow instruments and that the on/off switch not be blocked.

Throughout this manual, when reference is

made to a power

supply, it is assumed the customer is using a Hastings power supply. Hastings Power

supplies change as new technology becomes available. For knowledge of the most up-to-date Hastings
power supplies, please consult either Hastings sales staff or our website at

http://www.teledyne-hi.com

WARNING:

To prevent the spread of fires in the event of a fault, only use power supplies power

limited to no more than 150 VA. The current available from a power supply used with a 300
Series instrument should be no greater than 1.6 A. Hastings power supplies meet these
requirements.

1.4.2. Cables

Cables to power Hastings flow instruments connect from the 15 pin "D" connector on the back of the
power supply directly to any of the 300 Series flow instruments. More information about the available
cables can be found on our website at

http://www.teledyne-hi.com

«
...
8
9
10
11
12
...
»

Содержание HASTINGS HFC-302

































Отзывы:

Нет отзывов