manualshive.com logo in svg

Teledyne HASTINGS 2002, Инструкция по эксплуатации, Страница: 8 / 49

Поделиться
Скачать
Teledyne HASTINGS 2002 Скачать руководство пользователя страница 8

page 8

2.4    Control Unit Installation

Environment:

The instrument can be operated over a temperature range of 0

o

C to 50

o

C.  The instrument case

can be in NEMA 12 compliance (i.e. a reasonable degree of protection against dust and dripping

noncorrosive liquids in a panel configuration) with the front panel gasket installed.  To install, slide

the gasket over the back of the control unit prior to panel mounting (panel mount Instructions on

page 6). Also refer to panel mounting detail on page 43.

NOTE:  Back panel is not sealed.

Panel Mount Instructions:

The control unit can be panel mounted. See detail on page 43.  The hole dimensions on the panel

are 3.62" x 3.62"(92.8mm x 92.8 mm). Slide the neoprene gasket that was shipped with the control

unit onto the case from the back. Slide the controller through the panel cutout. Hold the hardware

against the side and tighten the two screws.

Transducer Cable Attachment:

The threaded connector attaches to the transducer.  A finger tight connection is adequate for

proper operation.  The 8-pin circular DIN connector attaches to the back panel (See Figure 4.1).

The transducer cable connects to the left hand connector when looking at the back.  The transducer

cable cannot connect to the I/O DIN connector but the seven pin I/O cable could be mistakenly

connected to the eight pin sensor connector. Ensure that the seven pin I/O cable is plugged into the

proper position.

I/O Cable Attachment:

The mating male plug to the I/O connector is supplied with the unit.  An I/O cable can be wired

with the 7-pin circular DIN connector to use the analog output, digital alarms or the remote zero

functions. The connector will accept 20 gauge or smaller wire. The pinout is shown in Figure 2.1

(back panel figure).  A detailed description of these pins is given in Section 4.

NOTE: It is recommended that the male plug be plugged into the female socket before

attempting to solder wires to the plug since this will keep the heat from deforming the

plug.

2.5    Initial Operation

Upon applying power to the control unit a pressure measurement will be given in  Torr for nitrogen.

However, it is recommended that the user follow the instructions for zeroing and adjusting the

output at atmospheric pressure in Section 3.4 ("Cal Mode").

Содержание HASTINGS 2002


















































Отзывы:

Нет отзывов