Teledyne CP030 Скачать руководство пользователя страница 9

Страница: 9 / 32

Operator’s Manual

Introduction

The CP030, CP030A, CP031, and CP031A current probes are designed for easy, highly

accurate current measurements. The compact probes offer wide bandwidth with

over-current protection. The probes utilize a combination of Hall-effect and transformer

technology which enables measurements to be made on DC, AC and impulse currents.
The CP030 and CP030A have a 50 MHz bandwidth and are designed to measure

continuous currents up to 30 Amp. The CP030-3M probe has a 10 MHz bandwidth and

is designed to measure continuous currents up to 30 Amp.

NOTE:

All CP030A probes, regardless of cable length, will indicate default probe

bandwidth of 50 MHz in the Attributes section of the Probe dialog.
The CP031 and CP031A have a 100 MHz bandwidth and are designed to measure

continuous currents up to 30 Amp.
The CP03x probes are compatible with any Teledyne LeCroy oscilloscope with a ProBus

interface running Windows XP Professional

or later.

The CP03xA probes are compatible with most Teledyne LeCroy oscilloscopes with a

ProBus interface running X-Stream™ firmware version 7.8.x.x or later. See table below.

Compatible

Compatible with Upgrade

Not Compatible

LabMaster 9MZi-A

DDA/SDA/WaveMaster 8 Zi/Zi-A/Zi-B

DDA/SDA/WavePro 7 Zi/Zi-A

HRO/WaveRunner 6 Zi

WaveRunner Xi/Xi-A/Mxi/Mxi-A

HDO8000, HDO6000, HDO4000

MDA800

WaveSurfer 10

WaveSurfer MXs/MXs-A/MXs-B

WaveSurfer Xs-A

WavePro 7000/7000A*

WaveSurfer Xs

†

LabMaster 10 Zi/Zi-A

LabMaster 9 SZi-A

SDA13000, SDA18000

SDA9000, SDA11000

WaveExpert

WaveRunner 6000/6000A

WaveSurfer 400

WaveSurfer 3000

All other legacy instruments

*Compatible if running Windows XP Professional and X-Stream 7.8.x.x or later. †Must be upgraded to Windows XP

Professional,

not

Windows XP Embedded. Contact your regional service center regarding upgrades.

With the ProBus interface, the probe becomes an integral part of the measuring

instrument. The bandwidth limit, Auto Zero and Degauss functions are all controlled

from the instrument’s touch screen user interface. The interface provides power to the

probe, so no external power supply is needed.

Содержание CP030

































Результаты поиска

Содержание CP030

Отзывы:

Бренды по названию

Популярные бренды

Teledyne CP030, Руководство оператора

Результаты поиска

Содержание CP030

Отзывы:

Бренды по названию

Популярные бренды