Teledyne 2105 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 98

Teledyne 2105 Скачать руководство пользователя страница 26

2105 Interface Module
Section 2 Installation and Operation

2-8

2.4 Antenna (2105Ci Only)

The 2105Ci uses a magnetic mount antenna and Serial Over
Internet Protocol (SOIP) communication to connect with other
units. (The module is also capable of CSD communication, but
this service is being phased out. See Section 2.5.1 for complete
information.) Phone service with a static IP address, rather than
a land line, provides efficient communication.

Note

The 2105Ci only works in a CDMA cellular service area with

1xRTT. See your local CDMA service provider for availability.

As you face the unit, the 2105Ci antenna connector socket is

located on the right hand side of the module (Figure 2-9). Remove
the connector cap from the socket and attach it to the cap on the
end of the antenna cable. To connect the antenna, press down on
the silver metal latch on the side of the module and push the
antenna’s connector into the socket.

CAUTION

Only use this antenna with 2100 Series Ci cellular modem
modules. Do not use this antenna with non-Ci equipment.

Figure 2-9

Antenna connected to 2105Ci

Note

For the transmitter to comply with FCC Maximum Permissible
Exposure (MPE) regulations, the antenna must be located a
minimum of 30 centimeters (12 inches) from the human body.

Note

When any communication connector is not in use, it should

always be capped. The cap will seal the connector to prevent
corrosion, prevent moisture from entering the unit, and improve
communications.

«
...
24
25
26
27
28
...
»

Содержание 2105



































































































Отзывы:

Нет отзывов