Teledyne 2105 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 98

Teledyne 2105 Скачать руководство пользователя страница 21

2105 Interface Module

Section 2 Installation and Operation

2-3

Figure 2-3 Identifying the voltage specification on the DB9 cable

WARNING

Injury and/or equipment damage can result from

connecting modules or cables to a power source exceeding
the specified operating voltage range. Check labeling on all
modules and cables for voltage ranges.

Note

All connected system components should share a common
supply ground.

2.2 Installation

Preparation

The 2100 Series components are often installed in confined

spaces. Some examples of confined spaces include manholes,
pipelines, digesters, and storage tanks. These spaces may become
hazardous environments that can prove fatal for those unpre-
pared. These spaces are governed by OSHA 1910.146 and require
a permit before entering.

WARNING

Avoid hazardous practices! If you use these instruments in

any way not specified in this manual, the protection
provided by the instruments may be impaired; this will
increase your risk of injury.

WARNING

The installation and use of this product may subject you to

hazardous working conditions that can cause you serious
or fatal injuries. Take any necessary precautions before
entering a worksite. Install and operate this product in
accordance with all applicable safety and health
regulations, and local ordinances.

Lower Voltage
DB9 Cable

Higher Voltage
DB9 Cable

«
...
19
20
21
22
23
...
»

Содержание 2105



































































































Отзывы:

Нет отзывов