manualshive.com logo in svg

Teledyne Lecroy WaveAce 1000, Справочник по командам, Страница: 66 / 92

Поделиться
Скачать
Teledyne Lecroy WaveAce 1000 Скачать руководство пользователя страница 66

WaveAce Remote Control 

 

Value  Description 

35 

Waveform data error. Invalid waveform data have been detected. 

36 

Panel setup error. An invalid panel setup data block has been detected. 

50 

No mass storage present when user attempted to access it. * 

51 

Mass storage not formatted when user attempted to access it. * 

53 

Mass storage was write protected when user attempted to create a file, to delete a file, or to format 

the device. * 

54 

Bad mass storage detected during formatting. * 

55 

Mass storage root directory full. Cannot add directory. * 

56 

Mass storage full when user attempted to write to it. * 

57 

Mass storage file sequence numbers exhausted (999 reached). * 

58 

Mass storage file not found. * 

59 

Requested directory not found. * 

61 

Mass storage filename not DOS compatible, or illegal filename. * 

62 

Cannot write on mass storage because filename already exists. *  

 

64 

920836 Rev B  

Содержание WaveAce 1000





























































































Отзывы:

Нет отзывов