Teledyne Lecroy WaveAce 1000 Скачать руководство пользователя страница 18

Страница: 18 / 92

WaveAce Remote Control

Short Form

Long Form

What the Command/Query Does

INTS

INTENSITY

Controls the brightness of the grid.

OFST

OFFSET

Allows output channel vertical offset adjustment.

PACU

PARAMETER_CUSTOM

Controls parameters with customizable qualifiers.

PAVA?

PARAMETER_VALUE?

Returns current parameter, mask test values.

PDET

PEAK_DETECTED

Enables or disables built-in peak detection function.

PERS

PERSIST

Enables or disables the persistence display mode.

PESU

PERSIST_SETUP

Selects display persistence duration.

RCPN

RECALL_PANEL

Recalls a front panel setup from mass storage.

SCSV

SCREEN_SAVE

Enables or disables the screen saver.

STO

STORE

Stores a trace in internal memory or mass storage.

STOP

Immediately stops signal acquisition.

TDIV

TIME_DIV

Modifies the timebase setting.

TRA

TRACE

Enables or disables the display of a trace.

TRCP

TRIG_COUPLING

Sets the coupling mode of the specified trigger source.

TRDL

TRIG_DELAY

Sets the time at which the trigger is to occur.

TRLV

TRIG_LEVEL

Adjusts the trigger level of the specified trigger source.

TRMD

TRIG_MODE

Specifies the trigger mode.

TRSE

TRIG_SELECT

Selects the condition that will trigger acquisition.

TRSL

TRIG_SLOPE

Sets the trigger slope of the specified trigger source.

VDIV

VOLT_DIV

Sets the vertical sensitivity.

WAIT

Prevents new analysis until current is completed.

WAVEFORM

Transfers a waveform from controller to scope.

WFSU

WAVEFORM_SETUP

Specifies amount of waveform data to go to controller.

920836 Rev B

Содержание WaveAce 1000





























































































Результаты поиска

Содержание WaveAce 1000

Отзывы:

Teledyne Lecroy WaveAce 1000, Справочник по командам, Страница: 18 / 92

Результаты поиска

Содержание WaveAce 1000

Отзывы: