Teledyne Lecroy WaveAce 1000 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 92

Teledyne Lecroy WaveAce 1000 Скачать руководство пользователя страница 46

WaveAce Remote Control

DISPLAY - HOR_POSITION, HPOS

The HOR_POSITION command repositions the geometric center of a zoom to display different portions

of the trace. Allowed positions range from division 0 through 10. If the source trace was acquired in

sequence mode, the shift will only apply to a single segment at a time.
The difference between the specified and the current horizontal position is applied to all zooms.

However, if the difference would cause any zoom trace to go outside the left or right screen

boundaries, the difference is adapted before being applied to the traces.
The HOR_POSITION? query returns the position of the geometric center of the zoom.

NOTE: Segment number 0 has the special meaning Show All Segments Unexpanded.

Command Syntax

Hor_POSition <hor_position>,<segment>

<hor_position>:= 0 to 10 DIV

<segment>:= 0 to max segments

NOTE: The segment number is only relevant for waveforms acquired in sequence mode; it is ignored in single

waveform acquisitions. When the segment number is set to 0, all segments are shown. The unit DIV is optional.

Query Syntax

Hor_POSition?

Response Format

Hor_POSition <hor_position>[,<segment>]

Example

The following instruction positions the center of the zoom at division 3:

HPOS 3

44

920836 Rev B

«
...
44
45
46
47
48
...
»

Содержание WaveAce 1000





























































































Отзывы:

Нет отзывов