Teledyne Lecroy CP031 Скачать руководство пользователя страница 25

Страница: 25 / 28

Operator’s Manual

Certifications

Declaration of Conformity — EMC

European Community

The probe meets the intent of EC Directive 2004/108/EC for Electromagnetic

Compatibility. Compliance was demonstrated to the following specifications as listed

in the Official Journal of the European Communities:
EN 61326-1:2006 EMC requirements for electrical equipment for measurement, control,

and laboratory use.

1 2 3

1 This product is intended for use in nonresidential areas only. Use in residential areas may cause

electromagnetic interference.

2 Emissions which exceed the levels required by this standard may occur when the probe is connected to

a test object.

3 To ensure compliance with the applicable EMC standards, use high quality shielded interface cables.

UROPEAN

ONTACT

Teledyne LeCroy Europe GmbH

Im Breitspiel 11c

D-69126 Heidelberg

Germany

Tel: (49) 6221 82700

Australia & New Zealand

The probe complies with the EMC provision of the Radio Communications Act per the

following standards, in accordance with requirements imposed by the Australian

Communication and Media Authority (ACMA):
AS/NZS CISPR 11:2011 Radiated and Conducted Emissions, Group 1, Class A.

USTRALIA

EALAND

ONTACTS

RS Components Pty Ltd.

Suite 326 The Parade West

Kent Town, South Australia 5067

RS Components Ltd.

Unit 30 & 31 Warehouse World

761 Great South Road

Penrose, Auckland, New Zealand

* Visit teledynelecroy.com/support/contact for the latest contact information.

www.

.com

[email protected]

1.800.561.8187

Содержание CP031





























Результаты поиска

Содержание CP031

Отзывы:

Похожие инструкции для CP031

Бренды по названию

Популярные бренды

Teledyne Lecroy CP031, Руководство оператора

Результаты поиска

Содержание CP031

Отзывы:

Похожие инструкции для CP031

Бренды по названию

Популярные бренды