manualshive.com logo in svg

Telect GMTXX, Руководство по установке, Страница: 14 / 22

Поделиться
Скачать
Telect GMTXX Скачать руководство пользователя страница 14

© Telect, Inc.,  All Rights Reserved, 132152-12 A0
1.509.926.6000  ::  telect.com

12

100A/60A Universal Voltage GMT Fuse Panels 
With Enhanced Power/Fuse & Bay Alarms

Power

  ::  HPGMTXX & GMTXX

The total load for all fuse outputs on each side must not exceed the panel’s load rating: either 60A or100A.

21.  Test power and polarity at input of each equipment load.

22.  If possible, replace one of the operable GMT fuses with a blown fuse to verify that the applicable FUSE Alarm 

LED turns red. Also, check the FUSE alarm terminals on the rear of the panel: 
• Expect an open circuit (00Ω) between Terminals C and NC. 
• Expect continuity (0Ω) between Terminals C and NO. Re-install operable GMT fuse before proceeding. 
 
If desired, connect remote, external audio/visual panel alarm indicator wires (solid wires, #22 to #18 AWG) to 
wirewrap PWR and FUSE alarm pins on rear of panel, as shown below on the right.

23.  If desired, connect remote audio/visual bay alarms indicator wires to the 

MAJ

 (major) and 

MIN 

(minor) alarm 

pins. Also install switch closure wires to the A (activate) and R (reference) pins, as shown above on the left, to 
control the bay alarm relay.

24.  Re-install terminal cover.

25.  Lastly, enable equipment loads one at a time to verify the proper operation of loads.

MAJ MIN

NC

C

NO

R
A

TO ALARM  
SYSTEM

TO ALARM  
SYSTEM

TO ALARM  
SYSTEM

TO ALARM  
SYSTEM

EXTERNAL

LOOP

CLOSURE

A - ACTIVATE
R - REFERENCE

NC
C

NO

PWR 

A

PWR 

B

FUSE

BAY ALARM TERMINALS

ENHANCED PANEL ALARM TERMINALS

Figure 12 - Alarm Schematics (Rear of Designation Card)

Содержание GMTXX























Отзывы:

Нет отзывов