Telect BCS II SIMPLEX Скачать руководство пользователя страница 15

Страница: 15 / 17

Telect, Inc. • USA +1.509.926.6000 • 52.33.3836.37.52
www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 117209-1 A0

Page 12

3.1.3 Patching

You can establish temporary patches using the I/O jacks on the front faceplate, as shown below.
This operation is intrusive and will interrupt the cross-connect, routing the signals through the
patch cords.

Figure 8 - Patching

4.1

Service

CAUTION

CAUTION! Only qualified technicians may install and maintain this product.

4.1.1 Owner Maintenance

Telect’s BCS II Simplex Repeater module does not need preventive maintenance. The only part
you can replace is the tracer lamp LED.

4.1.1.1 Replacing the Tracer Lamp LED

Procedure steps:

1. Pull the defective LED straight out with your fingers.

2. Align the replacement LED with the LED socket in the faceplate. Notice that the socket is

keyed, and the LED enters only one way.

ALERT

ALERT! Do not bend the LED’s two metal leads.

3. Gently insert the LED into the socket, as shown on the next page. If you encounter resis-

tance, do not force the LED into position. Move it until it slides easily into the jack module.

Network
Element

Repeater

or DSX

Network
Element

OX
IX
O
I

Repeater

Содержание BCS II SIMPLEX


















Результаты поиска

Содержание BCS II SIMPLEX

Отзывы:

Похожие инструкции для BCS II SIMPLEX

Бренды по названию

Популярные бренды

Telect BCS II SIMPLEX, Руководство пользователя

Результаты поиска

Содержание BCS II SIMPLEX

Отзывы:

Похожие инструкции для BCS II SIMPLEX

Бренды по названию

Популярные бренды