Telect BCS II SIMPLEX Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 17

background image

Telect, Inc. • USA +1.509.926.6000 • 52.33.3836.37.52
www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 117209-1 A0

Page 7

2.1.1.3 Power

–42 Vdc to –58 Vdc power reaches the module through the backplane connector on the chassis.
Power to the backplane connector block is delivered from the power distribution panel using 16–
22 AWG wire. See the chassis user manual for additional information on power transmission.
Because the repeater is an active product, Telect recommends using a dual-feed power source.

2.1.1.4 Technical Support (USA)

By e-mail: [email protected]
By phone: 888-821-4856 or 509-921-6161

2.1.1.5 Inspection

Compare the contents of the shipping container with the packing list. Call Telect if you are
missing anything.

NOTES:

Telect is not liable for shipping damage.

If the shipping container is damaged, keep it for the carrier’s inspection. Notify the carrier and
call Telect’s Customer Service Department: 1-800-551-4567 or 1-509-926-6000.

Keep the container until you have checked equipment operation. If you experience any kind
of problem, call Telect’s Customer Service Department. Use the original, undamaged con-
tainer if you are instructed to return the product to Telect.

2.2 Installing the Repeater

Procedure steps:

1. Identify the two network elements you wish to cross-connect.

2. Plan placement of the two repeater modules in relay racks, ensuring that

−

The distance between the network element and the repeater is correct for the system, ca-
bles in use and office procedures. This can be up to 450 feet.

−

The two repeater modules will not be more than 900 feet apart.

3. While wearing a grounding strap, remove the repeaters from their anti-static bags, touching

the module edges only.

4. Set the jumpers on each module for the appropriate data rate, as shown below. (Factory set-

ting is T3.)

«
...
8
9
10
11
12
...
»

Содержание BCS II SIMPLEX


















Отзывы:

Нет отзывов

Похожие инструкции для BCS II SIMPLEX

Бренд: ZETRON Страницы: 259

Бренд: U-Prox Страницы: 17

Бренд: Orava Страницы: 19

Бренд: PEHA Страницы: 4

Бренд: Somogyi Elektronic Страницы: 20

HDBaseT Repeater 4K

Бренд: StarTech.com Страницы: 2

Бренд: Zibro Страницы: 14

Бренд: Xantech Страницы: 2

Бренд: HOMCOM Страницы: 8

Бренд: Euromatic Страницы: 16

Бренд: Dantherm Страницы: 135

Бренд: Range Страницы: 4

Бренд: Warmtech Страницы: 32

Бренд: Air King Страницы: 6

Бренд: Watlow Страницы: 2

Бренд: GMI Страницы: 7

Бренд: Plein Air Страницы: 14

Бренд: Quality Heating Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды