background image

LNB rotation for ideal reception in Europe’s extreme

(South-West or South-East) areas

Remember that the outside converter (a.k.a. LNB) has its own assembly position which must
be complied with. Otherwise you will not receive any signal. The pre-set mounting position
for the LNB is along the centre line of the disk (fig. A). With this configuration, the Voyager
G3 system works correctly in most European countries. However, if you are in areas very
far from the satellite orbital position, it might be necessary to adjust the converter angle. In
particular, if you wish to receive transmissions from the satellites Astra 19E, Astra 28E or
HotBird 13E, while you find yourself in Portugal or Morocco, your converter angle should be
adjusted as shown in (fig. B), while if you are in Turkey, to receive the same satellites you
should set your converter to the position (fig. C).

Place

Position

HotBird 13E

Astra 19E

Astra 28E

Lisbona

B

25°

28°

37°

Casablanca

B

27°

34°

41°

Ankara

C

22°

15°

1) Remove the LNB protective cover by screwing out the 3 screws
2) Loosen the screws on the LNB locking U-bolt
3) Turn in the Clockwise (West) or Anti-clockwise (South-East) direction
4) Lock the LNB again by screwing down the screws
5)  Close back the LNB protective cover and screw down the 3 screws

9

Содержание VoyagerG3 65

















Отзывы: