background image

Wireless shock sensor

Detects abrupt movements. The wireless shock sensor, 
located on the roller shutter, warns via radio of the attempt to 
break in. Buzzer to be installed in the control unit included.

Power supply: battery.

Buzzer

Safety devices

Sensor

Transmitter TVMIO868P02

1

2

3

4

NEW

5

6

7

1

2

3

4

NEW

5

6

7

1

2

3

4

NEW

5

6

7

1

2

3

4

NEW

5

6

7

1

2

3

4

NEW

5

6

7

1

2

3

4

NEW

5

6

7

CHANGING THE BATTERY 

Keep the batteries out of the reach of children. Call a doctor immediately if a battery is swallowed. Explosion hazard if 
the battery is substituted incorrectly. Replace the battery with a CR 2032 type battery only. Always wrap the battery up, 
both when it is being stored and when it is being disposed of. The battery should not come into contact with other metal 
objects as it could cause the battery to run down, catch fire or be damaged. Dispose of damaged or finished batteries  
immediately in compliance with the law. To this end, contact the authorities for safeguarding the environment or the 
centre for disposing of waste materials in your area. Do not throw the battery away with household rubbish.
   1 - Remove the screw on the back.
2,3 - Open the lid. 
4,5 - Take the old batteries out and put the new ones in the same way. Pay attention to correct polarity (+/-)!
6,7 - Close the transmitter with the screw.

2-channel hand transmitter

Carrier frequency 

 

 

868.3 MHz

Power supply  

 

 

3V ± 10% 

(lithium battery CR2032)

Consumption when transmitting  12 mA
Operating temperature range 

-10°÷ +55° C

Warnings:

 keep this manual transmitter out of the reach of children and animals. Do not use the manual transmitter in places or where 

systems are sensitive to radio emissions (e.g. airports, hospitals). Do not keep or use the manual transmitter in places that are damp, where 
there is steam, high air humidity, dust or where it is exposed to the direct rays of the sun or similar environmental conditions. Do not let the 
manual transmitter drop: it could be damaged or its range of action reduced. The operator is in no way protected against interference from 
other telecommunication equipment or systems (e.g. authorised radio systems working on the same frequency range). If you are having 
problems with its range of action, fix the manual transmitter up high (under the sunshade in a car for instance). Do not use your nails to press 
the key as they could damage the keys.Hereby Teleco automation s.r.l. declares that the products comply with the essential requirements 
and other relevant provisions, established by the Directive 1999/5/EC. The declaration of conformity can be consulted on the web site: www.
telecoautomation.com/ce In the view of a constant development of their products, the manufacturer reserves the right for changing technical 
data and features without prior notice. 

Содержание TVPRP868N09





















Отзывы: