background image

14

6.1 Auto close time setting

This procedure configures the time lapse between complete opening and the automatic closure (if enabled).
The default time is 

5 seconds

. It is possible to set the time from 5 seconds to 90 seconds.

Note:

 The procedure can be executed only 

within 30 seconds from power on

The control unit will add by default 5 seconds to the time measured in the procedure.

Press the internal 

P3 

button of a memorized transmitter and keep it pressed for 

5 seconds

. The buzzer will emit one beep.

Release and press it again 

eight times

 

within 5 seconds

. The buzzer will make 

two 

beeps at the end.

In case of time-out, the control unit will sound four beeps and exit the procedure automatically.

Press once 

P3

 to start the counting of time. The buzzer will make one beep. 

Press again 

P3

 to stop the counting after the desired lapse. The value will be memorized by the control unit.

START

STOP

6.2 Courtesy light time setting

This procedure configures the time of activation of the courtesy light. 
The default time is 

60 seconds

. It is possible to set the time from 60 seconds to 12 hours.

Note:

 The procedure can be executed only 

within 30 seconds from power on

The control unit will add by default 60 seconds to the time measured in the procedure.

within 5 sec.

8

times

 

keep it pressed

(       5 s)

START

STOP

P3 button is 
located inside 
the transmitter.

within 5 sec.

5

times

 

keep it pressed

(       5 s)

Press the internal 

P3 

button of a memorized transmitter and keep it pressed for 

5 seconds

. The buzzer will emit one beep.

Release and press it again 

five times

 

within 5 seconds

. The buzzer will make 

three 

beeps at the end.

In case of time-out, the control unit will sound four beeps and exit the procedure automatically.

Press once 

P3

 to start the counting of time. The buzzer will make one beep. 

Press again 

P3

 to stop the counting after the desired lapse. The value will be memorized by the control unit.

P3 button is 
located inside 
the transmitter.

P3

memorized

P3

memorized

P3

memorized

P3

memorized

P3

memorized

P3

memorized

P3

memorized

P3

memorized

Содержание TVPRP868N09





















Отзывы: