Telebyte 458-CC-16 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 51

Telebyte 458-CC-16 Скачать руководство пользователя страница 11

Model 458-CC-16/458-CM (16-Slot Chassis & Control Module) Rev I

Page 6

User Command Interface

ASCII command set compliant with IEEE 488.2 and in Hex ASCII two-character bytes per 488
bus data byte.

RS-232 - LF, Baud rate 300 to 19200, commands use terminating character (Carriage Return),
eight Data Bits, one Stop Bit.

RS-232 Mode Command List



All Set card lengths, English/Metric mode and Echo enable/disable are maintained
during power off in both RS-232 and IEEE modes. Manual control is enabled at power
on.

id
Identify model no. and rev.

Read model no. and software revision code

re
Read last error

Read description of last error

ee
Echo enable

Echo all inputs and format output for terminal display

ed
Echo disable

Inputs not echoed and format output for user control program

h
Help RS232 command list

Read RS232 command list

cs:BR
Configure serial

Where BR = 300, 600, 1200, 2400, 4800, 9600 or 19200

«
...
9
10
11
12
13
...
»

Содержание 458-CC-16




















































Отзывы:

Нет отзывов