manualshive.com logo in svg

Teldat REGESTA 1, Руководство по установке и настройке

Поделиться
Скачать
Teldat REGESTA 1 Скачать руководство пользователя страница 22

OK

4.4.1 Standard Commands

Here we are going to summarize the standard AT commands that the REGESTA 1 supports.

4.4.1.1 Serial Port Configuration

Syntax

AT+IPR=<bps>

Description

Configures the serial port speed.

<bps> transfer speed in bits per seconds.

The permitted speeds are:

• 1200

• 4800

• 9600

• 19200

• 57600

• 115200

Example

AT+IPR=115200

OK

Syntax

AT+IFC=<dce-dte>,<dtedce>

Description

Permits you to Activate/Deactivate the flow control

The permitted speeds for the <dce-dte> and <dtedce> fields are:

• 1,1 SW flow control (XON/XOFF)

• 2,2 HW flow control

• 0, 0 Without flow control

Example

AT+IFC=2,2

OK

Syntax

AT+ICF=<config>,<par>

Description

Permits you to establish the number of data bits, parity and stop bits.

The permitted values for the config> and <port> fields are:

• 3,4 (8N1) Without parity.

• 2,0 (8O1) Odd.

• 2,1 (8E1) Even.

Example

AT+IFC=3,4

OK

4 Configuration

Teldat S.A.

18

REGESTA 1

Содержание REGESTA 1
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды