Tektronix PS 503A, Инструкция по эксплуатации

Страница: 56 / 57

CALIBRATION TEST EQUIPMENT REPLACEMENT
Calibration Test Equipment Chart
This chart compares TM 500 product performance to that of older Tektronix equipment. Only those
characteristics where significant specification differences occur, are listed. In some cases the new instrument
may not be a total functional replacement. Additional support instrumentation may be needed or a change in
calibration procedure may be necessary.
Comparison
of
Main Characteristics
DM 501 replaces 7D13
PG 501 replaces 107
PG 501 - Risetime less than 3.5 ns into
50 Ω.
107 - Risetime less than 3.0 ns into
50 Ω .
108 PG 501 - 5 V output pulse; 3.5 ns Risetime. 108 - 10 V output pulse; 1 ns Risetime.
111 PG 501 - Risetime less than 3.5 ns; 8 ns
Pretrigger pulse delay.
111 - Risetime 0.5 ns; 30 to 250 ns
Pretrigger Pulse delay.
114 PG 501 - ±5 V output. 114 - ±10 V output. Short proof output.
115 PG 501 - Does not have Paired, Burst, Gated,
or Delayed
pulse mode; ±5 V dc
Offset. Has ±5 V output.
115 - Paired, Burst, Gated, and Delayed
pulse mode; ±10 V output.
Short-proof output.
PG 502 replaces 107
108 PG 502 - 5 V output 108 - 10 V output.
111 PG 502 - Risetime less than 1 ns; 10 ns
Pretrigger pulse delay.
111 - Risetime 0.5 ns; 30 to 250 ns
Pretrigger pulse delay.
114
PG 502 - ±5 V output
114 - ±10 V output. Short proof output.
115 PG 502 - Does not have Paired, Burst, Gated,
Delayed & Undelayed pulse mode;
Has ±5 V output.
115 - Paired, Burst, Gated, Delayed & Un­
delayed pulse mode; ±10 V output.
Short-proof output.
2101 PG 502 - Does not have Paired or Delayed
pulse.
Has ±5 V output.
2101 - Paired and Delayed pulse; 10 V
output.
PG 506 replaces 106
PG 506 - Positive-going trigger output signal
at least 1 V; High Amplitude out­
put, 60 V.
106 - Positive and Negative-going trigger
output signal, 50 ns and 1 V; High
Amplitude output, 100 V.
067-0502-01 PG 506 - Does not have chopped feature.
0502-01 - Comparator output can be alter­
nately chopped to a reference
voltage.
SG 503 replaces 190,
190A, 190B SG 503 - Amplitude range 5 mV to 5.5 V p-p.
190B - Amplitude range 40 mV to 10 V p-p.
191
SG 503 - Frequency range 250 kHz to 250 MHz. 191 - Frequency range 350 kHz to 100 MHz.
067-0532-01 SG 503 - Frequency range 250 kHz to 250 MHz. 0532-01 - Frequency range 65 MHz to 500 MHz.
TG 501 replaces 180,
180A
TG 501 - Marker outputs, 5 sec to 1 ns.
Sinewave available at 5, 2, and 1 ns.
Trigger output - slaved to marker
output from 5 sec through 100 ns.
One time-mark can be generated at a
time.
180A - Marker outputs, 5 sec to 1
µ s
.
Sinewave available at 20, 10,
and 2 ns. Trigger pulses 1,10,
100 Hz; 1, 10, and 100 kHz.
Multiple time-marks can be
generated simultaneously.
181 TG 501 - Marker outputs, 5 sec to 1 ns. Sine­
wave available at 5, 2, and 1 ns.
181 - Marker outputs, 1, 10, 100, 1000,
and 10,000 µs plus 10 ns sinewave.
184
TG 501 - Marker outputs, 5 sec to 1 ns. Sine­
wave available at 5, 2, and 1 ns.
Trigger output - slaved to marker
output from 5 sec through 100 ns.
One time-mark can be generated at
a time.
184 - Marker outputs, 5 sec to 2 ns. Sine­
wave available at 50, 20, 10, 5,
and 2 ns. Separate trigger pulses
of 1 and .1 sec; 10, 1, and .1 ms;
10 and 1 µs . Marker amplifier pro­
vides positive or negative time
marks of 25 V min. Marker
intervals of 1 and .1 sec; 10, 1,
and .1 ms; 10 and 1 µ
s
.
2901 TG 501 - Marker outputs, 5 sec to 1 ns. Sine­
wave available at 5, 2, and 1 ns.
Trigger output - slaved to marker
output
from 5 sec through 100 ns.
One time-mark can be generated at
a time.
2901 - Marker outputs, 5 sec to 0.1 /
js
.
Sinewave available to 50, 10,
and 5 ns. Separate trigger pulses,
from 5 sec to 0.1
/
js
.
Multiple
time-marks can be gene­
rated simultaneously.
NOTE: All TM 500 generator outputs are short-proof. All TM 500 plug-in instruments require TM 500-Series Power Module.
REV. A, OCT 1975