Tektronix P6910 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 48

background image

Operating basics

1.

Connect the probe to the square pins on the SUT.

The probe is compatible with differential and single-ended signals. The (-)
lead can be connected to the (-) side of a differential signal or to ground.

NOTE.

Connect lead sets in groups or to individual locations on the SUT. If

necessary, use the grouper from the accessories kit to hold the lead set together.

2.

Connect the way station ground connector to a ground on the SUT.

NOTE.

The lead sets have true differential inputs. For single-ended use, the

negative input of the lead set can be connected to ground. However, the ground
lead from each way station is provided to connect the probe ground to the SUT
ground.

8

P6910 General Purpose Probe Instruction Manual

«
...
20
21
22
23
24
...
»

Содержание P6910

















































Отзывы:

Нет отзывов

Похожие инструкции для P6910

Бренд: GE Страницы: 8

Moisture Image 1 Series

Бренд: GE Страницы: 110

DigitalFlow GS868

Бренд: GE Страницы: 74

DigitalFlow GS868

Бренд: GE Страницы: 81

Бренд: Baker Hughes Страницы: 59

Бренд: Baker Hughes Страницы: 2

Бренд: Panametrics Страницы: 67

Бренд: Panametrics Страницы: 108

Transport PT878

Бренд: GE Страницы: 97

Бренд: 4iiii Страницы: 3

Бренд: Aaronia Страницы: 47

Бренд: ICS Страницы: 2

Бренд: CAISSON Страницы: 5

Бренд: Abus Страницы: 168

Бренд: OHAUS Страницы: 76

Бренд: Midcontinent Страницы: 6

Бренд: AEMC Страницы: 4

Бренд: Bontempi Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды