Tektronix DPO3000 Series Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 79

background image

Maintenance

If you have not already done so, carefully remove the oscilloscope and its
accessories from the shipping carton and inspect them for damage. Save the
shipping carton for repacking or storage.

Repacking

Use a corrugated cardboard shipping carton having a test strength of at least
275 pounds (125 kg) and with an inside dimension at least six inches (15.25 cm)
greater than the instrument dimensions.

If the instrument is being shipped to a Tektronix Service Center, enclose the
following information:

The owner’s address

Name and phone number of a contact person

Type and serial number of the instrument

Reason for returning

A complete description of the service required

Seal the shipping carton with an industrial stapler or strapping tape.

Mark the address of the Tektronix Service Center and also your own return address
on the shipping carton in two prominent locations. See www.tektronix.com/service
to

fi

nd a service center near you.

Storage

The oscilloscope should be stored in a clean, dry environment. The following
environmental characteristics apply for both shipping and storage:

Temperature range: -20 °C to +60 °C

Altitude: To 15,000 m

See the

MSO3000 and DPO3000 Series Speci

fi

cations and Performance

Veri

fi

cation Technical Reference

for a complete listing of the environmental

characteristics.

MSO3000 and DPO3000 Series Digital Phosphor Oscilloscopes Service Manual

4–17

«
...
53
54
55
56
57
...
»

Содержание DPO3000 Series
















































































Отзывы:

Нет отзывов

Похожие инструкции для DPO3000 Series

Бренд: Konig & Meyer Страницы: 2

Бренд: Mustang Страницы: 9

Бренд: META Страницы: 33

Бренд: HoverCam Страницы: 7

Бренд: B-Tech Страницы: 8

Бренд: ricoo Страницы: 12

Бренд: Hama Страницы: 22

Бренд: U-Line Страницы: 6

Бренд: Datalogic Страницы: 2

Бренд: B-Tech Страницы: 8

Бренд: Nanit Страницы: 52

Бренд: CIM med Страницы: 12

Бренд: wavebone Страницы: 12

Бренд: Easee Страницы: 40

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 1

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды