Tektronix DPO3000 Series Скачать руководство пользователя страница 11

Страница: 11 / 79

Service Safety Summary

Service Safety Summary

Only quali

ed personnel should perform service procedures. Read this

Service

Safety Summary

and the

General Safety Summary

before performing any service

procedures.

Do Not Service Alone.

Do not perform internal service or adjustments of this

product unless another person capable of rendering

rst aid and resuscitation is

present.

Disconnect Power.

To avoid electric shock, switch off the instrument power, then

disconnect the power cord from the mains power.

Use Care When Servicing With Power On.

Dangerous voltages or currents may

exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.

To avoid electric shock, do not touch exposed connections.

MSO3000 and DPO3000 Series Digital Phosphor Oscilloscopes Service Manual

vii

Содержание DPO3000 Series
















































































Результаты поиска

Содержание DPO3000 Series

Отзывы:

Похожие инструкции для DPO3000 Series

Бренды по названию

Популярные бренды

Tektronix DPO3000 Series, Руководство по обслуживанию

Результаты поиска

Содержание DPO3000 Series

Отзывы:

Похожие инструкции для DPO3000 Series

Бренды по названию

Популярные бренды