Главная
/
Tektronix
/
DPO2304SX
/
Печатная инструкция

Tektronix DPO2304SX, Печатная инструкция

Поделиться

Страница: 717 / 920

background image

What do you want to do next?

Learn about interpolation.

Learn about using the MultiView Zoom feature.

Go to a step-by-step procedure for displaying waveforms.

Using the MultiZoom feature

Use the instrument MultiZoom feature to magnify an acquisition vertically, horizontally, or in both dimensions to let you see the
fine detail in your signals without changing the acquisition parameters (sample rate, record length, and so on). For example, to
temporarily expand the front corner of a pulse to inspect its aberrations, push the front-panel MultiZoom button to expand it
horizontally and vertically.

To help you use Mulitzoom effectively, consider how it operates on waveforms:

■

When zooming vertically, the instrument expands up to four zoomed areas at one time. The zoomed areas can all be on the
same waveform or they can be on different Channel, Math or Reference waveforms. Each zoomed area has its own vertical
position and factor.

■

When zooming horizontally, the Zoom Source is either the acquisition waveform or one of the zoomed areas.

■

When zooming either horizontally or vertically, Zoom expands or contracts the waveform by the Zoom Factor.

What do you want to do next?

Go to a step-by-step procedure for displaying waveforms.

Go to a step-by-step procedure for using MultiView Zoom.

Waveform measurement

Automatic measurements

All channel, reference, and math waveforms can serve as sources for automatic measurements. Some measurements, such as
Delay and Phase, require two sources.

NOTE. Automatic measurements are not available on digital channels.

The following automatic measurement categories are available:

■

■

■

(miscellaneous)

■

■

Communication

Click the category for a list of the measurements that you can choose from in each category.

The instrument can take and update up to eight measurements at one time. You can apply measurements to any combination of
sources. For example, you can take all eight measurements on Channel 1, or you can take measurements on a combination of
channel waveforms, math waveforms, reference waveforms, and/or histograms.

Oscilloscope reference

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

685

«
...
715
716
717
718
719
...
»

Содержание DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DPO2304SX

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Бренд: ACCU-CHECK Страницы: 104

Бренд: AccuMed Страницы: 14

Бренд: TAS Страницы: 25

PowerXL DX-NET-ETHERNET2-2

Бренд: Eaton Страницы: 48

Power Xpert C445

Бренд: Eaton Страницы: 2

Бренд: Fellowes Страницы: 20

Бренд: Idmed Страницы: 2

Varycolor MICRO 150HTI

Бренд: JB-Lighting Страницы: 18

Бренд: ZOLL Страницы: 37

Бренд: Wacker Neuson Страницы: 34

Бренд: Wagan Страницы: 4

Бренд: Wachs Страницы: 22

ARCHISHAPE 2.0 Linear

Бренд: Osram Страницы: 7

MEGA STROBE/DMX

Бренд: American DJ Страницы: 2

Бренд: Bauerfeind Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды