TekTone Tek-SELECT II SM401, Руководство по эксплуатации, установке и обслуживанию

Страница: 9 / 16

IL603 Tek-SELECT
®
II Manual • Page 5
2.1 Master Station
Call another station:
1. If the
TALK
light is not illuminated red, select the desired
station by pressing its associated selector button. The
following will occur:
a. The
TALK
light will illuminate yellow.
b. The selected station
CALL
light will illuminate red.
c. If the called station is non-private, sound from the
called station will be heard.
d. Set volume as needed.
Note: If a station button is pressed while the
TALK
light
is red, the called station will not be connected. Press
the selector button again to release it, and wait until the
TALK
light goes out. If the station is left selected, it will
be connected when the system is free, but this may
result in an undesirable howling noise if more than one
master was waiting for the system to be free.
2. Press the
TALK
button to speak, release to listen.
3. When finished, press the selected station button again
to extinguish the
CALL
and
TALK
lights.
Answer a call from a master at a remote:
1. The incoming call will be announced by a chime or tone,
and by a green
CALL
light.
2. If the
TALK
light is not illuminated red, press the selector
button associated with the illuminated
CALL
light. The
following will occur:
a. The
TALK
light will illuminate yellow.
b. The selected station
CALL
light will change from green
to red.
c. If the called station is non-private, sound from the
calling station will be heard.
Note: If the station button is pressed while the
TALK
light is red, the selected station will not be connected.
Press the selector button again to release it, and wait
until the
TALK
light goes out.
3. Press the
TALK
button to speak, release to listen.
4. When finished, press the selected station button again
to extinguish the
CALL
and
TALK
lights.
Answer a call from a master at a master:
1. Calls from masters are not indicated by a light, but may
be preceded by a short tone signal. Master calls are
announced by voice.
2. To answer:
a. If the
PRIVACY
light is illuminated, press the
PRIVACY
button to turn privacy off.
b. It is not necessary to operate any other controls.
Reply by voice.
Open the door (if installed):
1. Press the
DOOR
button (identified by a key).
Page all stations (if installed):
1. If the
TALK
light is not illuminated red, press the
PAGE
switch to the right. The following will occur:
a. The
TALK
light will illuminate yellow.
b. The
PAGE
light will illuminate yellow.
c. If “talk back” is enabled, sounds from called stations
will be heard.
2. When finished, press the
PAGE
switch to the left to
extinguish the
TALK
and
PAGE
lights.
Monitor a room:
1. If the
MONITOR
light is not illuminated red, press the
MONITOR
button, and then press the button associated
with the desired station. The following will occur:
a. The
MONITOR
light will illuminate yellow.
b. The
MONITOR
light associated with the selected station
will illuminate red.
c. If the monitored station is non-private, sounds from
that station will be heard.
d. Set volume as needed.
2. When the intercom is in use by another station, the
monitoring will be interrupted, but will return when the
other station is finished.
3. When finished monitoring, press the selected station
button and the
MONITOR
button to extinguish the
MONITOR
and
CALL
lights.
Note: Do not attempt to use the
MONITOR
function if the
MONITOR
light is red. To do so may result in a loud noise
from the intercom.
2.2 Remote Station
Call a master:
1. If only one
CALL
button is available, press the button. If
there is more than one
CALL
button, press the button to
call the desired master.
2. If the remote has a
PRIVACY
switch, and if privacy is
selected, press the
PRIVACY
button to turn the privacy
OFF.
3. Reply by voice when spoken to.
Section 2.0 — OPERATING INSTRUCTIONS