background image

4

When filling the cart, LOAD FROM 
THE BOTTOM TO THE TOP,

keeping weight evenly distributed.

When rolling the cart from one location to another, 
AVOID OBSTACLES ON THE FLOOR, like small parts or 
debris. Use care when crossing seams in concrete floors.

OPEN ONLY ONE DRAWER at a time.

OPERATING

INFORMATION ABOUT YOUR CART

LOADING

Bottom Pan 

200 lb.

Top Pan

W

eight Cap

acities

200 lb.

Drawers (if present)

100 lb.

per

drawer

Casters

1000 lb.

250 lb.

per caster

NOTE: Included keys work for drawers and lid

•  The drawer capacities shown here refer to drawer slide 

function, the ability of the drawer slides to move while 

bearing weight. DO NOT RELY ON THESE CAPACITIES 

ALONE TO AVOID TIPPING.

•  When loading, consider the effect of fully extended 

drawers. Keep weight evenly distributed. DO NOT 

PLACE HEAVY LOADS IN FRONT HALF OF DRAWERS.

•  DO NOT SIT OR STAND ON this cart. 
•  DO NOT ALLOW CHILDREN TO OPERATE 

this cart.

•  CLOSE AND LATCH ALL DRAWERS before 

moving the cart.

•  ENGAGE CASTER BRAKES each time the 

cart reaches a new location.

USE ONLY ON LEVEL, HARD, SMOOTH SURFACES. Do not use on sloped driveways or rough surfaces.

WARNING:

 THIS CART MAY TIP OVER CAUSING INJURY OR DEATH.

3

2

1

Содержание ORG65103

























Отзывы: