TEKNA 702736 Скачать руководство пользователя страница 9

TB-1016-A

9

Parts Replacement/

Maintenance

NEEDLE PACKING  

REPLACEMENT INSTRUCTIONS

1.  Remove trigger using a Star (T20) driver.  

(See pictures 9-1 & 9-2)

2.  Remove fluid adjusting knob and needle  

spring with spring pad from gun.  

(See pictures 9-3 & 9-4)

3.  Remove fluid needle from gun body.  

(See picture 9-5)

4.  Loosen and remove packing nut using a straight 

blade screwdriver. (See picture 9-6)

5.  Discard old packing and packing spring if replacing. 

Clean packing if reusing. Also clean packing spring 

and nut. (See picture 9-7)

6.  Partially insert clean fluid needle into gun  

and place packing nut, spring, and new packing 

onto needle. Be sure tapered end of packing  

goes into gun first. (See pictures 9-7 & 9-8)

7.  Insert fluid needle all the way into gun body  

seating in fluid nozzle.

8.  Tighten needle packing nut by hand, then  

remove fluid needle.

9.  Tighten needle packing nut fully, using a straight 

blade screwdriver. Don’t over tighten.  

(See picture 9-6)

10.  Reinstall fluid needle, needle spring, spring  

pad, and fluid adjusting knob. (See pictures 9-5, 9-4 

& 9-3) A drop or two of lubricant on parts assures 

smooth operation.

11.  Reinstall trigger. (See pictures 9-2 & 9-1)  

A drop of lubricant assures smooth operation.

12.  Trigger gun fully and screw in fluid adjusting  

knob until it stops. Back it off 1/2 turn and gun will 

have full needle travel.

13.  Trigger gun several times to verify  

proper operation.

FLUID INSERT REPLACEMENT/

MAINTENANCE

The fluid insert and seal are NOT replaceable.  

Don’t remove these parts. (See picture 9-9)  

No maintenance is required for these parts other  

than cleaning the internal bore.

SPREADER VALVE ASSEMBLY 

REPLACEMENT/MAINTENANCE

The spreader valve assembly can be replaced if 

damaged (See picture 9-10). Remove using a  

14 mm wrench. The internal seal can be replaced  

and is included in the TEKNA Gun Rebuild Kit.

9-1

9-2

9-3

9-4

9-5

9-6

9-7

9-8

9-9

9-10

DON'T REMOVE FLUID INSERT 
AND SEAL IN GUN BODY

Содержание 702736

















Отзывы: