Teikoku CHEMPUMP NC Series Скачать руководство пользователя страница 4

Страница: 4 / 38

Teikoku USA | Chempump

Instruction Manual NC-Series 0220

Contents

Introduction 2

1. General Information

NC-A50-10 Curve..................................................32

Appx. J.

NC-A60-10 Curve..................................................33

Appx. K. Decontamination Certification

and Flushing Procedure .........................................34

Appx. L.

Repair Receipt Policy ..............................................37

Tables

Table 2-1.  Conditions Indicated on the TRG Meter ...................9
Table 2-2.  TCO Maximum Coil Currents ...................................9
Table 2-3.  NC-Series Electrical Data 60 hz (Oil Filled Stator) ....11
Table 2-4.  NC-Series Electrical Data 60 hz (Dry Stator) ............11
Table 2-5.  Electrical Wiring Data 230 Volt, 3 Phase .................12
Table 2-6.  Electrical Wiring Data 460 Volt, 3 Phase .................12
Table 2-7.  Electrical Wiring Data 575 Volt, 3 Phase .................13
Table 2-8.  Coolant Flow Rates ...............................................13
Table 2-9.  Recirculation Flow Rates ........................................14
Table 4-1.  Recommended Tools for

Disassembly & Reassembly .....................................19

Table 4-2.  Recommended Tools for Inspection ........................19
Table 4-3.  NC-Series Bearing and Journal Dimensions ............20
Table 4-4.  End Play ................................................................20
Table 4-5.  Parts......................................................................22
Table 4-6.  Coil Resistance Values ...........................................22
Table 4-7.  L Motor Coil Resistance Values ..............................22

Figures

Содержание CHEMPUMP NC Series







































Результаты поиска

Содержание CHEMPUMP NC Series

Отзывы:

Похожие инструкции для CHEMPUMP NC Series

Бренды по названию

Популярные бренды

Teikoku CHEMPUMP NC Series, Инструкция по эксплуатации

Результаты поиска

Содержание CHEMPUMP NC Series

Отзывы:

Похожие инструкции для CHEMPUMP NC Series

Бренды по названию

Популярные бренды