Teikoku CHEMPUMP NC Series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 38

background image

Thank you for purchasing a Chempump

TM

NC-Series pump.

Please carefully read this instruction manual and all Safety Warnings prior to use.

Introduction

Safety Terms

Please pay close attention to these terms. When you see them
in this manual, read the information thoroughly and follow the
instructions given.

Attention!

Indicates careful attention is required. The instruc-
tion includes protective information for the device and
product.

Caution!

Ignoring this warning can cause personal injury and/or
damage to the device and product.

Hazard!

Ignoring this warning can cause serious injury or even
death. It can also be used to alert against unsafe practices.

NOTE:

Information included in NOTES gives additional helpful

information and recommendations.

Applicable Standards and Regulations

The NC-Series pump conforms to the following standards:

1. American Society of Mechanical Engineers (ASME) B-16.5

2. Canadian Standards Association (CSA): UL 778 CSA 22.2

No 108

Product Warranty Period

This product is warranted for two years from date of delivery.
Please refer to Teikoku USA’s Terms and Conditions of Sale for
additional warranty coverage and restrictions.

Rights

All rights on products manufactured by Teikoku, corresponding
software, and this instruction manual are registered to Teikoku
Electric Mfg Co., Ltd.

It is not permitted to reproduce or transmit any portion of this
instruction manual unless prior written consent has been ob-
tained from Teikoku USA Inc., Teikoku Electric Mfg Co., Ltd. or
its subsidiaries.

Chempump

TM

is a trademarks of Teikoku Electric Mfg. Co., Ltd.

Teikoku Rotary Guardian

TM

and TRG

TM

are trademarks of Teikoku

Electric Mfg. Co., Ltd.

«
1
2
3
4
...
»

Содержание CHEMPUMP NC Series







































Отзывы:

Нет отзывов

Похожие инструкции для CHEMPUMP NC Series

Бренд: Sanden Страницы: 20

Бренд: DAB Страницы: 64

Бренд: WAGNER Страницы: 100

flexoTHERM exclusive VWF 57/4

Бренд: Vaillant Страницы: 20

AquaMax Eco Expert

Бренд: Oase Страницы: 60

Nessie Plug&Spray NPS 1CS

Бренд: Danfoss Страницы: 12

Бренд: PerformancePro Страницы: 15

Бренд: LEYBOLD Страницы: 34

Бренд: RainPoint Страницы: 32

Бренд: F.F. Group Страницы: 28

Бренд: Malmbergs Страницы: 12

Shoebox Heat Pump

Бренд: Kensa Heat Pumps Страницы: 20

Бренд: Elnur Страницы: 7

GRACO TORPEDO G1275-2P100

Бренд: QED Страницы: 12

Бренд: Amada Страницы: 21

Бренд: EBARA Страницы: 88

Бренд: Ulvac Страницы: 55

Бренд: Adam Pumps Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды