background image

Thank you for purchasing the Teikoku Type-R (Plan 13-SE) refrigeration canned motor pump.  
Please carefully read this instruction manual and all Safety Warnings prior to use.

Quick Start Guide 

is included in the Appendix of this manual.

Introduction

Safety Terms

Please pay close attention to these terms. When you see them 
in this manual, read the information thoroughly and follow the 
instructions given.

Attention!

Indicates careful attention is required. The instruction in-
cludes protective information for the device and product.

Caution!

Ignoring this warning can cause personal injury and/or 
damage to the device and product.

Hazard!

Ignoring this warning can cause serious injury or even 
death. It can also be used to alert against unsafe practices.

NOTE: 

Information included in NOTES gives additional helpful 

information and recommendations.

Applicable Standards and Regulations

The Teikoku Type-R (Plan 13-SE) pump conforms to the follow-
ing standards: 

1.  Japanese Industrial Standard (JIS)

2.  Japan Electrical Manufacturers’ Standard (JEM) 

3.  American Society of Mechanical Engineers (ASME) B-16.5

4.  Canadian Standards Association (CSA): UL 778 CSA 

22.2 No 108

5.  International Institute of Ammonia Refrigeration (IIAR): 

ANSI/IIAR 2-2014

Product Warranty Period

This product is warranted for two years from date of delivery. 
Please refer to Teikoku USA’s Terms and Conditions of Sale for 
additional warranty coverage and restrictions. 

Rights

All rights on products manufactured by Teikoku, corresponding 
software, and this instruction manual are registered to Teikoku 
Electric Mfg Co., Ltd. 

It is not permitted to reproduce or transmit any portion of this 
instruction manual unless prior written consent has been ob-
tained from Teikoku USA Inc., Teikoku Electric Mfg Co., Ltd. or 
its subsidiaries.

Teikoku Rotary Guardian

TM

 and TRG

TM

 are trademarks of 

 

Teikoku Electric Mfg. Co., Ltd. 

Содержание API-685




























Отзывы: