Maintenance (Continued)
5. Reinstall washer and snap ring on
shaft, (See Figure 4).
6. Install new lip seal, (See Figure 5).
Lubricate lip seal with a small
amount of Aqualube or a lithium-
based grease.
7. Reassemble impeller, washer, and
impeller screw (Models 4RK45A
through 4RK49A).
Reassemble impeller and impeller
nut (Models 4RK62A and 4RK63A).
8. Reinstall capacitor (Single phase
only). See Figure 6 for electrical
connections to capacitor.
9. Fill motor with clean dielectric oil
(Part No. U197-8A). To allow room
for expansion, oil level with cold
motor should be about 1/4"
(6-7mm) above top of motor
assembly.
10. Inspect capacitor cover O-Ring;
replace if damaged. If it is not
nicked or scratched, clean and
reinstall.
NOTE:
It is good practice to replace
O-Ring each time pump is serviced.
11. Reconnect motor lead wires to
connector. Reference color code
markings. Reinstall capacitor cover.
6
Teel Operating Instructions and Parts Manual
4RK45A, 4RK46A, 4RK47A, 4RK48A, 4RK49A, 4RK62A and 4RK63A
Teel Submersible Effluent and
Sewage/Solids Handling Pumps
®
E
N
G
L
I
S
H
Limited Warranty
DAYTON ONE-YEAR LIMITED WARRANTY.
Teel
®
submersible effluent and sewage/solids handling pump, Models covered in this manual, are
warranted by Dayton Electric Mfg. Co. (Dayton) to the original user against defects in workmanship or materials under normal use for one year after
date of purchase. Any part which is determined to be defective in material or workmanship and returned to an authorized service location, as
Dayton designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced at Dayton’s option. For limited warranty claim
procedures, see PROMPT DISPOSITION below. This limited warranty gives purchasers specific legal rights which vary from jurisdiction to jurisdiction.
LIMITATION OF LIABILITY.
To the extent allowable under applicable law, Dayton’s liability for consequential and incidental damages is expressly
disclaimed. Dayton’s liability in all events is limited to and shall not exceed the purchase price paid.
WARRANTY DISCLAIMER.
Dayton has made a diligent effort to provide product information and illustrate the products in this literature accurately;
however, such information and illustrations are for the sole purpose of identification, and do not express or imply a warranty that the products are
MERCHANTABLE, or FIT FOR A PARTICULAR PURPOSE, or that the products will necessarily conform to the illustrations or descriptions.
Except as provided below, no warranty or affirmation of fact, expressed or implied, other than as stated in the “LIMITED WARRANTY” above is made
or authorized by Dayton.
PRODUCT SUITABILITY.
Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain
purposes, which may vary from those in neighboring areas. While Dayton attempts to assure that its products comply with such codes, it cannot
guarantee compliance, and cannot be responsible for how the product is installed or used. Before purchase and use of a product, review the product
applications, and all applicable national and local codes and regulations, and be sure that the product, installation, and use will comply with them.
Certain aspects of disclaimers are not applicable to consumer products; e.g., (a) some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you; (b) also, some jurisdictions do not allow a limitation
on how long an implied warranty lasts, consequently the above limitation may not apply to you; and (c) by law, during the period of this Limited
Warranty, any implied warranties of implied merchantability or fitness for a particular purpose applicable to consumer products purchased by
consumers, may not be excluded or otherwise disclaimed.
PROMPT DISPOSITION.
Dayton will make a good faith effort for prompt correction or other adjustment with respect to any product which proves to
be defective within limited warranty. For any product believed to be defective within limited warranty, first write or call dealer from whom the
product was purchased. Dealer will give additional directions. If unable to resolve satisfactorily, write to Dayton at address below, giving dealer’s
name, address, date, and number of dealer’s invoice, and describing the nature of the defect. Title and risk of loss pass to buyer on delivery to
common carrier. If product was damaged in transit to you, file claim with carrier.
Manufactured for Dayton Electric Mfg. Co., 5959 W. Howard St., Niles, Illinois 60714 U.S.A.
Leads From
Stator
White
Red
Black
Green
Black
Capacitor
Figure 6 – Electrical Connections to
Capacitor
Install washer,
then clip
Figure 4
Slide seal
onto shaft
Figure 5