background image

6

Teel Operating Instructions and Parts Manual

4RJ45

Teel Engine Driven High Pressure
Centrifugal Pump

®

E

N
G

L

I

S

H

Symptom

Possible Cause(s)

Corrective Action

SYSTEM

No water delivered

1. Pressure required by system at design 

1. Compare pump pressure and flow rate against 

flow rate exceeds pressure rating of 

pump performance chart. Reduce system pressure 

pump

requirement. Increase pressure capability of pump

2. Obstruction in suction piping

2. Locate and remove obstruction. Attach strainer

3. Suction lift too high

3. Check with gauge or measure vertical distance 

between water surface and center line of pump, 
allowing for friction loss in suction pipe. Reduce 
rate of flow to obtain desired lift. Refer to pump
performance chart

4. Leaky suction line or connection 

4. Repair or replace suction line. Tighten connections

admitting air

Not enough water 

1. Pressure required by system at design 

1. Compare pump pressure and flow rate against 

delivered

flow rate exceeds pressure rating of 

pump performance chart. Reduce system pressure 

pump

requirement. Increase pressure capability of pump

2. Obstruction in suction piping

2. Locate and remove obstruction. Attach strainer

3. Suction lift too high

3. Check with gauge or measure vertical distance 

between water surface and center line of pump, 
allowing for friction loss in suction pipe. Reduce 
rate of flow to obtain desired lift. Refer to pump 
performance chart

4. Leaky suction line or connection 

4. Repair or replace suction line. Tighten connections

admitting air

Not enough  

1. Pressure required by system at design  

1. Compare pump pressure and flow rate against  

pressure

flow rate exceeds pressure rating of  

pump performance chart. Reduce system pressure 

pump

requirement. Increase pressure capability of pump 

2. Obstruction in suction piping

2. Locate and remove obstruction. Attach strainer

3. Suction lift too high

3. Check with gauge or measure vertical distance 

between water surface and center line of pump, 
allowing for friction loss in suction pipe. Reduce 
rate of flow to obtain desired lift. Refer to pump 
performance chart

Troubleshooting Chart

Содержание 4RJ45









Отзывы: